Catalog excerpts
Small Motors Gearmotors Motion Controls
Open the catalog to page 1ELECTRIC COMPANY STOCK CATALOG NR General Information Safety and Installation Precautions Bodine products are designed and manufactured to comply with applicable safety standards. Since even well-built apparatus can be installed or operated in a hazardous manner, it is important that safety considerations be observed by the user. With respect to the load and environment, the user must properly select, install, and use the apparatus. It is the responsibility ot the equipment manufacturer or the individual installing the apparatus to take diligent care in installing it. Local electrical and...
Open the catalog to page 3SLUE To reverse dwxbon, transpose blue leads To reverse dIrectIon. trans pose blue leads BLACK-YELTR. LINE BLACK BLUE-YELTR. BLACK BLUEI, GRN-YELTR.(GRD) Connect as shown above for clockwe black and black-ye1 tr leads rotation while v~ewwg the output shaft To reverse dlrectlon transpose the Control -type Shunt wound motors and gearmotors have 18” long cable with molded plug as illustrated below. Plug mates with receptacleon matching Bodinespeedcontrols. Plug can be omitted if not required. See connection diagram No. 074 10085 for color coding of leads within the cable. 07410085;5 Lead...
Open the catalog to page 4APPLICATION NOTE Shunt Wound (SH) Field vs. Permanent Magnet (PM) Field Drives The accompanying chart illustrates and compares the performance curves of two Bodine 1/4 hp DC motors as operated without speed controls at rated voltage and direct-current of unity form factor (FF= 1.0). For gear-motorsthe speeds would be divided by the ratio. Operation of the motors with Bodine SCR speed-torque controls is illustrated on pages 19. Essentially, the Bodine SCR speed controls flatten the slope (improve the regulation) of the speed-torque curves between the no-load and rated load points....
Open the catalog to page 5Self-ventilated or enclosed • High Efficiency Windings for Low Current Draw • Class 8 Insulation tor Long Life • Locked Bearings for Minimal Endplay General “N-1" motors incorporate four piece construction—center ring, two shields, and base—provides design flexibility and easy maintenance. The shields are carefully fitted to the center ring with rabbeted joints and held by four screws. This assures rigidity for positive bearing alignment and the accurate, uniform air gap required for quiet, efficient operation. The ''30R" motor features efficient permanent split capacitor windings. This...
Open the catalog to page 6TYPE “N” AND “24A” MOTORS (DC) • Long-Life Oversize Brushes • Skewed Armature for Smooth Operation • Inherent High Starting Torque • Noise-Tested Ball Beanngs • Light and Compact • External Access for Brush Inspection • Encoder-Ready Model Available General The “N-1” motor incorporates four piece construction— center ring, two shields, and base —provides design flexibility and easy maintenance. The shields are carefully fitted to the center ring with rabbeted Joints and held by four screws, This assures rigidity for positive bearing alignment and the accurate, uniform air gap required for...
Open the catalog to page 7SHUNT WOUND—115 VOC—Totally Enclosed CAPACITOR. PERMANENT SPLIT. NON-SYNCHRONOUS—115 V —60 Hz.—1 Ph.—Totally Enclosed “34R" Motors • Removable Rigid Base Mounting • Fan Cooled for High Output Power • Lower Operating Temperature Prolongs Winding and Lubricant Life • Aluminum Center Ring and End Shields for High Thermal Efficiency and Light Weight • Locked Bearing Minimizes Shaft Endplay • Noise Tested Ball Bearings • Permanent Grease Lubrication General Self-ventilated N-trame motors employ highly effective forced fan ventilation systems which make possible greater output for a given frame...
Open the catalog to page 8TYPE “N-1R” GEARMOTORS (AC or DC) Single (to 4.8 Lb-in.) and double (to 7 Lb-in.) reduction, right angle "N-1R" Gearmotor (double reduction) • Die Cast Motor Shield and Gear Housing • Tapped Holes Permit Rotating Gear Head * Porous Bronze Output Shaft Bearings • Up-Type Oil Seals • Shielded Ball Bearings on Motor Shaft • Motor Shaft Extension ♦ General The “N-1R” single and double reduction worm gearmotors are designed for transmitting relatively low torques. Grease lubricated ball bearings are employed on motor shaft. Worms are of hardened alloy steel. Primary gears are bakelite...
Open the catalog to page 9SHUNT WOUND—115 VOC.—Totally Enclosed. Non-Ventilated PERMANENT MAGNET FIELD—130VDC—Total Enclosed "24A-3F” Gearmotor (DC) • Die Cast Gear Housing • Shielded Ball Bearings on Motor Shaft • Separable Worm * Bronze Sleeve Bearings on Output Shaft * External Access tor Brush Inspection General The “N-1RH” and “N-3R" gearmotor combines our "3R' gearhead with our “N-1” motor frame and is designed for transmitting moderate torque. The worm is separable, hardened and ground, and driven by a cross pin and slot. The gearhead has a laminated bakelite gear tor moderate torque and quietness. Gearmotor...
Open the catalog to page 10• Die Cast Gear Housing • Shielded Sail Bearings on Motor Shaft • Separable Worm • Bronze Sleeve Bearings on Output Shaft • Oil Seal on Drive Shaft General These gearmotors are based on our “3R" gearhead and are designed for transmitting moderate torque The worm is separable, hardened and ground, and driven by a cross pin and slot. The "3R" gearhead has a laminated bakelite gear for moderate torque and quietness. The output shaft Is supported by bronze sleeve bearings which are lubricated through felt wicks and reservoirs and includes an oil seal. Notes Mounting positions—see page 3 •...
Open the catalog to page 11Single reduction, right angle...to 37 Lb-in. Speed Rpm "34R-3F" Gearmotor • Die Cast Gear Housing • Shielded Ball Bearings on Motor Shaft • Separable Worm • Bronze Sleeve Bearings on Output Shaft • Oil Seal on Drive Shaft General These gearmotors are based on our “3R" and “3F" gearheads and are designed for transmitting moderate torque The “N-3R” employs our “N-3" motor frame while the “34R-3F" utilizes our thermally efficient "34R" Frame design. The worm is separable, hardened and ground, and driven by a cross pin and slot. The "3R" gearhead has a laminated bakelite gear for moderate...
Open the catalog to page 12All BODINE ELECTRIC COMPANY catalogs and technical brochures
-
PLANETARY BLDC GEARMOTORS
2 Pages
-
Standard Products
4 Pages
-
Bodine Electric Handbook
252 Pages
-
42R-FX AC Gearmotor
2 Pages
-
DC control selection guides
12 Pages
-
AC control selection guides
3 Pages