RSMUX3
6Pages

RSMUX3-FO RSMUX3-FO - Optical multiplexer of 2x RS232/422/485 serial interfaces • • • • • • • • Functionality RSMUX3-FO is a multiplexer of 2x RS232/422/485 streams into fiber. Multiplexer allows connection of RS232/422/485 serial interfaces over fiber links with the maximum distance of 100km and provides complete isolation between devices and resistance to disturbance occurring along transmission path. Depending on the specific versions, device can be connected using multimode or single-mode fiber. WDM and SFP versions also available. In basic version device is equipped with one fiber optic interface, version with two optical interfaces is also available. Optimized and automatic tracking mechanisms continuity and its restoration after removing the failure allows maintenance-free operation for the lifetime. RSMUX3-FO also performs the function of converting any signals involving the exchange, for example, RS-232 to RS-485 or RS-422, which is realized by means of two devices connected to each fiber. RSMUX3-FO provides fully transparent operation. Each serial interface is sampled with a frequency of 20Mhz, which allows on data throughput of the RS to 230.4 Kbps (RS-232) and 2Mbps (RS-485/RS-422) with +/-60ns pulse time distortion. RS485 ports can be set up for 2-wire or 4wire. Depending on the version of the device, multiplexer can work in point to point (with optical path protection), bus Multiplexer of 2x RS232/422/485 interfaces with screw connection over fiber links, The device has one or two optical interfaces Available configurations: POINT-POINT, RING, BUS or two independent converters in one housing The configuration of the device through DIPswitch Transmission speed up to 2Mbps for RS-485, to 230.4kbps for RS-232 Support for the protocol IEC103 (FO) only for the 'MM' Single alarm contact NC/NO Supply voltage range 110-260V DC or 100240V AC and ring topologies. Serial interfaces can be configured through DIP switches. In addition, each port has two independent LEDs activity data in the transmitter and receiver, which greatly simplifies the process of installation, commissioning and maintenance. The unique power directly in the range of 110-260V DC and 100-240V AC. The protection of connection The device is available in versions with one or two optical interfaces. In the case of devices with two optical ports can create connections with protection for the fiber optic link. However, when building a ring on the basis of one optical port (it cannot be a version of the WDM) we have no redundancy. Fiber ports can be implemented by the built-in optical interfaces (single or dual fiber) or by SFP. In the case of the creation of the ring it is possible to simultaneously connect up to 64 devices. However, after you select with the letter 'D' (an option only for the version of the 'MM'), we obtain two independent converters in one chassis without protection, with common power supply and from the fiber we have support for the protocol IEC103. Generally, IEC103 protocol is for the 'MM', the only multimodowej allowing direct connection of fiber optic cable with a controller of another manufacturer that supports this standard.

RSMUX3-FO Example of such application is presented on the drawing below. Fig 1. Example of the work in point-to-point also with protection Fig. 3 Example of work in the ring topologies with protection for the version with dual-port optical (single fiber WDM) and work in the ring topology without protection for the version with single-port optical Fig.4 Example of the work using the standard IEC103 protocol to directly connect fiber optic cable with the controller (only for the 'MM')

Management is done through the built-in dip-switch, which is used for the type of interface choices and topology operation. Supported transmission standards • EIA-232 • EIA-422 • EIA-485 Supported protocols • Profibus • Modbus Supported standards, recommendations and directives EMC Security*: • PN-EN 55011:2012 - Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics Limits and methods of measurement • PN-EN 55022:2010/AC:2011 - Information technology equipment - Radio disturbance characteristics – Limits and methods of measurement • PN-EN...

2x screw connection (cable 1.5mm 2) RS-232 - transmission speed 0-230.4kbps RS-422/485 - transmission speed 0-2Mbps Power supply Optical interface One or two optical interfaces: SM, MM, WDM, CWDM, DWDM Fiber type: 9/125um, 50/125um, 62.5/125um Connector: SC/PC or SFP, for 850nm only ST/PC Ranges depending on the type of optical port Physical design • • • Dimensions: 103x84x53mm Weight: 0.5 kg DIN rail mounting view - front Supply voltage range: - 100 - 240V AC - 110 - 260V DC Power Consumption: up to 4W galvanic isolation of power supply Galvanically isolated input Power connector -...

RSMUX3-FO–(S)–(X)–(P)–(Z)–(B)–(T)–(U) Power supply: C – 100-240V AC /110-260V DC Working temperature: Without symbol – range 0° to +50°C T – range -40° to +75°C Support Bi- Phase interface Without symbol – standard version B – Support Bi-Phase interface Type of serial interface connectors: Without symbol – version with four RJ45 connectors Z – version with two screw connectors Optional converter functions: Without symbol – standard version P – version with protection D** – double, two independent converters in one housing without protection only for version 'MM' Optional for WDM for Wx 1 –...

RSMUX3-FO version with 1x FO SFP module, with two screw terminals, with Bi-Phase interface, operating temperature from -40°C to +70°C, power supply 36-60V DC Additional accessories: • • • • • • • • • • • • • • LT-19-01 mounting rail for four RSMUX2 devices in the 19"/2U rack (