Catalogs >
BinMaster >
DPM-200 Digital Panel Meter

DPM-200 Digital Panel Meter
6Pages

Catalog excerpts

4-20 mA & Relay Output FEATURES • 4-20 mA, ± 10 V, TC & RTD Inputs • 4-Digit Display, 0.56" (14.2 mm) or 1.20" (30.5 mm) • Type 4X, NEMA 4X, IP65 Front • 1/8 DIN Shallow Depth Case 3.6" Behind Panel • Operating Temperature Range of -40°C to 65°C • Free MeterView® Software - Configuration & Data Acquisition • Sunlight Readable Display • Universal Power Supply 85-265 VAC • 12-36 VDC/12-24 VAC Power Option • 24 VDC @ 200 mA Transmitter Power Supply Options • 2 Relays + 4-20 mA Output Options • Pump Alternation Capability • USB, RS-232, & RS-485 Serial Communication Options • Free Modbus® RTU with Serial Adapter Option • Copy Meter Settings to Other Meters • Max/Min Display • High & Low Alarms with Multiple Reset Actions

Open the catalog to page 1

Digital Panel Meter DPM-200 & DPM-200 X2 Displays Front Panel NEMA 4X Rated UV Resistant Sunlight Readable Models (Actual Size Digits) 1.2" (30.5 mm) Display Powerful Relay Functionality FEATURE RICH & SIMPLE TO USE All relay functions are set up from the front panel or from a PC running MeterView® software. • Automatic reset only • Automatic or manual reset • Latching or non-latching relays • Pump alternation control • On and off time delays from 0 to 199 seconds • Fail-safe operation is user selectable The DPM-200 digital panel meter is one of the most versatile digital panel meters on...

Open the catalog to page 2

Digital Panel Meter DPM-200 EASY SETUP AND PROGRAMMING The DPM-200 is easily setup and programmed using the simple four-button programming method. The meter can also be programmed using a PC and free MeterView software or “cloned” with the Copy function. There is only one switch on the entire meter, no jumpers, and no need to ever open the case. Programming with Four Front Panel Buttons The DPM-200's four front panel buttons keep the user in control of the programming process. Programming From a PC with MeterView® MeterView® software allows all PD765 DPM-200 setup parameters to be...

Open the catalog to page 3

Digital Panel Meter Process & Temperature Inputs The DPM-200 is factory calibrated to accept 4-20 mA, ±10 VDC, type J, K, T, or E thermocouples and 100 Ω platinum RTDs. Process inputs can be scaled with or without applying an input for virtually any engineering units. Temperature inputs can be programmed to display in degrees Fahrenheit or Celsius and the type K thermocouple can display up to 2300 °F. Current & Voltage Inputs Setting up the meter to accept a current or voltage input could not be easier. All setup is performed with the front panel buttons and there are no Rear View Rear View...

Open the catalog to page 4

Digital Panel Meter DPM-200 SPECIFICATIONS Except where noted all specifications apply to operation at +25°C. General Display: DPM-200: 0.56" (14.2 mm); DPM-200 X2: 1.20" (30.5 mm) red LED, 4 digits (-1999 to 9999) Display Intensity: Eight user selectable levels Front Panel: NEMA 4X, IP65; panel gasket provided Programming Methods: Four front panel buttons, cloning with Copy feature, PC with MeterView software, and Modbus registers. Noise Filter: Programmable 2 to 199 (0 will disable filter) Display update Rate: Process/RTD: 3.7-5/sec; TC: 1.8-2.5/sec Overrange: Display flashes...

Open the catalog to page 5

Digital Panel Meter DPM-200 Serial Communications Compatibility: EIA-232, and EIA-485 Protocol: Modbus RTU Meter Address: Modbus protocol: 1 to 247 Baud Rate: 300 to 19,200 bps Transmit Time Delay: Programmable 0 to 199 ms Data: 8 bit (1 start bit, 1 stop bit) Parity: None (2 stop bits), even, or odd (Modbus only) Byte-to-Byte timeout: 0.01 to 2.54 seconds (Modbus only) turn around Delay: Less than 2 ms (fixed) Refer to Modbus Serial Communications Protocol manuals for details. DPM-200 PD765 • Standard Display Models Disclaimer The information contained in this document is subject to change...

Open the catalog to page 6