Trophy Gravity Feed Manual Gun
8Pages

SERVICE MANUAL BINKS SV100 HVLP GRAVITY FEED SPRAY GUN 7042-6931-4 The following instructions provide the necessary information for the proper maintenance of the Binks SV100 gravity feed spray gun. Please read and understand all the information in this document in order to get the maximum performance from your new SV100 gravity spray gun. The SV100 spray gun is the result of quality engineering and development activity. The result is an ergonomic product with reduced triggering effort and fine atomization. The HVLP air cap has been specifically designed to comply with local regulatory air quality restrictions. The specification table details the operating parameters of the gun to achieve those compliant conditions. In addition, the relatively low air flow rate of the SV100 spray gun will help in containing overspray. The SV100 spray gun should be operated under the safety directions outlined in this literature. Your safety and the safety of others depend on your thorough understanding of the material contained on the Part Sheet. If you have any questions or do not understand the content in this literature, call your nearest service representative. For HVLP Compliance: 26 psi inlet pressure delivers (with SV100-693K cap) 10 psi air cap pressures at 12 cfm air volume Gun Body: Cast Aluminum Fluid Path: Fluid Nozzle: Stainless Steel Fluid Needle: Stainless Steel Fluid Inlet Size:

EN In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. ! CAUTION Hazards or unsafe practices which could result in minor personal injury, product or property damage. Important installation, operation or maintenance information. Read the following warnings before using this equipment. READ THE MANUAL Before operating finishing equipment, read and understand all safety, operation and maintenance information provided...

EN OPERATION AND MAINTENANCE INSTRUCTIONS Your new SV100 Gravity Feed Spray Gun is exceptionally rugged in construction and is built to stand up under hard, continuous use. However, like any other fine precision instrument, its most efficient operation depends on a knowledge of its construction, operation, and maintenance. Properly handled and cared for, it will produce beautiful, uniform finishing results long after other spray guns have worn out. Separator Filter with Air Regulator Gravity Feed Cup Fluid Inlet SET-UP FOR SPRAYING (Figure 1) CONNECTING GUN TO AIR HOSE Air should be...

EN GENERAL SPRAY INSTRUCTIONS To reduce overspray and obtain maximum efficiency, always spray with the lowest possible fluid/air pressure that produces an acceptable spray pattern. Generally use up to 20 psi air at gun inlet. Unusually heavy, difficult to atomize materials may require up to 26 psi at gun inlet. See Specifications on page 1. Excessive atomizing air pressure can increase overspray, reduce transfer efficiency and with some materials, result in poor finish quality from dry spray. SPRAY TECHNIQUE The first requirement for a good resultant finish is the proper handling of the...

EN BINKS SV100 HVLP GRAVITY FEED SPRAY GUN PARTS LIST (When ordering, please specify Part No.) ITEM NO. ★ -5053 Gravity Gun Fluid Tip and Needle Replacement Kit K (includes 1.4 and 2.0 mm tips) ■ K-5057 Soft Parts Kit • K-5053-20 Gravity Gun Fluid Tip and Needle Replacement Kit (includes 2.0 mm tip) s SGK-537-K Baffle and 5 ea. Packings

EN AIR NOZZLE, FLUID NOZZLE, FLUID NEEDLE NOTE To reduce overspray and obtain maximum efficiency always spray with the lowest possible atomizing air pressure. 1. ll nozzles and needles are precision made. They A should be handled with care. 2. o not make any alterations in the gun. To do so D could cause finishing difficulties. 3. o clean nozzles, soak them in solvent to dissolve T any dried material, then blow them clean with air. 4. o not probe any of the holes in the nozzles with D metal instruments. If probing is necessary, use only a tool that is softer than brass. Never use metal...

EN ACCESSORIES Cleaning Brushes 42884-214-K5 (3/8") 42884-215-K10 (5/8") 29-3100-K6 Scrubs® Hand Cleaner Towels These brushes are helpful in cleaning threads and recesses of gun body. GFC-501 (Acetal) 20 Oz. Cup 54-4720 (Aluminum) 1-Liter Cup Gravity Feed Cups Scrubs ® are a premoistened hand cleaner towel for painters, body men and mechanics that go where you go and no water is needed. These gravity feed cups are designed to be used with EXL, FLG, Compact, SV100, 95G and M1-G gravity feed spray guns. Spray Gun Lube SSL-10-K12 (2 oz. bottle) Compatible with all paint materials; contains no...

EN WARRANTY POLICY Binks products are covered by Finishing Brands one year materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Finishing Brands, will void all warranties. For specific warranty information please contact the closest Finishing Brands location listed below. Finishing Brands reserves the right to modify equipment specifications without prior notice. DeVilbiss®, Ransburg®, BGK®, and Binks® are registered trademarks of Carlisle Fluid Technologies, Inc., dba Finishing Brands. ©2015 Carlisle Fluid Technologies, Inc., dba...