Catalogs >
Binks >
Pump Packing Lubricant (Lube) - (FR Liquid 40)

Pump Packing Lubricant (Lube) - (FR Liquid 40)
7Pages

Catalog excerpts

Pump Packing Lubricant (Lube) - (FR Liquid 40) - 1

COPYRIGHT ITW Industrial Finishing PRODUCT RELATED HEALTH DATA SHEET > INGREDIENTS CAS REG NO. WGT. % ACGIH TWA OSHA TWA UNITS ACGIH TWA OSHA TWA AIHA WEEL TWA UNITS Diethylene glycol 111-46-6 40 - 60 > 3 Water 7732-18-5 40 60 Polyalkylene Glycol Proprietary 10- 30 ppm mg/m > 3 Proprietary Ingredients Proprietary Mixture < 4 >

Open the catalog to page 1

Pump Packing Lubricant (Lube) - (FR Liquid 40) - 2

PRODUCT NAME: Pump Packing Lubricant (FR Fluid 40) MSDS#: MSDS-20 MAJOR ROUTE(S) OF ENTRY: Skin contact. Eye contact. Inhalation. Ingestion. ACUTE EFFECTS: Eye: This product can cause eye irritation with short-term contact with liquid, mists or vapors. Symptoms include stinging, watering, redness, and swelling. Skin: This product can cause mild, transient skin irritation with short-term exposure. The severity of irritation will depend on the amount of material that is applied to the skin and the speed and thoroughness that it is removed. Symptoms include redness, itching, and burning of the...

Open the catalog to page 2

Pump Packing Lubricant (Lube) - (FR Liquid 40) - 3

PRODUCT NAME: Pump Packing Lubricant (FR Fluid 40) MSDS#: MSDS-20 damaged or if pain or irritation persists. Thoroughly clean contaminated cloth-ing before reuse. Discard contaminated leather goods. INGESTION: If swallowed, give two glasses of water to drink. Never give anything by mouth to a person who is not fully conscious. Induce vomiting only upon advise of a physician. Seek medical attention immediately. INHALATION: Remove victim immediately to fresh air. If victim is not breathing, immediately begin rescue breathing. If breathing is difficult, 100 percent humidified oxygen should be...

Open the catalog to page 3

Pump Packing Lubricant (Lube) - (FR Liquid 40) - 4

PRODUCT NAME: Pump Packing Lubricant (FR Fluid 40) MSDS#: MSDS-20 > HANDLING PRECAUTIONS: Protect from temperature extremes and direct sunlight. Maintain operating temperatures as low as possible. Do not allow operating temperatures to exceed 66C (150ںF). Loss of water through evaporation during use can reduce safety and performance efficiency. To ensure fire resistance, water content must be maintained above 35%. Product container is not designed for elevated pressure. Do not pressurize, cut, weld, braze, solder, drill, or grind on containers. Do not expose product containers to flames,...

Open the catalog to page 4

Pump Packing Lubricant (Lube) - (FR Liquid 40) - 5

PRODUCT NAME: Pump Packing Lubricant (FR Fluid 40) MSDS#: MSDS-20 EXPOSURE GUIDELINES: See section 2 WORK HYGIENIC PRACTICES: As with all chemicals, use good personal hygiene practices. Wash hands and other exposed skin areas with plenty of mild soap and water before eating, drinking, smoking, use of toilet facilities or leaving work. DO NOT use gasoline, kerosene, solvents, or harsh abrasive skin cleaners. Keep this and other chemicals out of reach of children. Minimize body contact with this product. Wash contaminated clothing before reuse. > APPEARANCE: Fluorescent, Pink. PHYSICAL STATE:...

Open the catalog to page 5

Pump Packing Lubricant (Lube) - (FR Liquid 40) - 6

PRODUCT NAME: Pump Packing Lubricant (FR Fluid 40) MSDS#: MSDS-20 Anuria from tubular degeneration can prove fatal within a few days. In a 1937 case study, 105 fatalities occurred among 353 people who ingested a solution of sulfanilamide in an aqueous mixture containing 72% diethylene glycol. The symptoms included nausea, dizziness, and pain in the kidney region. In a few days, oliguria and anuria, with death resulting from uremic poisoning, (Amdur, Doull and Kiaasen, 1991). Autopsies revealed that the principal signs of intoxication were in the kidneys and liver (cortical necroses,...

Open the catalog to page 6

Pump Packing Lubricant (Lube) - (FR Liquid 40) - 7

PRODUCT NAME: Pump Packing Lubricant (FR Fluid 40) MSDS#: MSDS-20 regional US EPA office for guidance concerning case specific disposal issues. DO NOT pressurize, cut, weld, braze, solder, drill, grind, or expose this products empty container to flames, sparks, heat or other potential ignition sources. DO NOT attempt to clean it. Empty drums and pails should be drained completely, properly bunged or sealed, and properly sent to a re-conditioner. Dispose of waste at an approved disposal facility in compliance with all current Local, State/Province, and Federal/Canadian laws and regulations....

Open the catalog to page 7