MX412
28Pages

MX412 12:1 Pump Systems for Air Assist & Airless Finishing Patent 7,603,855 SPECIFICATIONS Ratio: Maximum air inlet pressure: Maximum fluid pressure: Air consumption @ 20 cycles/min. @ 8 bar [116 psi] air inlet pressure: Maximimum recommended continuous cycle rate: Stroke length: Fluid inlet connection: Fluid outlet connection: Wetted parts materials of construction: 3/4" NPS(m) 3/8" BSP(m) / 3/8" NPS(m) Stainless Steel, Tungsten Carbide, Hard Chrome, PTFE, Polyethylene, Leather Sound level: We reserve the right to change the specifications without prior notice. © BINKS 2013 Replaces Part Sheet 77-2912R-9

In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product or property damage. Important installation, operation or maintenance information. Read the following warnings before using this equipment. Read the Manual Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the...

High Pressure Can cause serious injury if equipment is installed or used incorrectly— Read, Understand, and observe all Warnings and Instructions in this Manual. Install, Operate or service this Equipment Only After All Instructions Are Clearly Understood. It is the responsibility of the employer to place this information into the hands of the operator. Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product or property damage. AVOID STATIC SPARKING...

HAZARD EXPLOSION SAFEGUARDS 1. f installing this equipment in a potentially explosive I atmosphere, check the ATEX equipment category and temperature ratings meet the requirements for the zoned area. STATIC ELECTRICITY Use of this equipment in a potentially explosive atmosphere. 2. heck electrical continuity of the air supply to earth — C should be no greater than 106 . Vapors from flammable liquids can catch fire or explode from static electricity discharges. SPECIAL CONDITIONS FOR SAFE USE REQUIRED BY ATEX CERTIFICATION 3. lectrically bond all metallic equipment to earth. E Should be no...

STARTUP AND OPERATION (Part numbers referenced are contained in MX412 Bare Pump Assembly Part Sheet: 77-2906.) GROUNDING THE BINKS PUMP To prevent static charging igniting the flammable spray material, the BINKS pump must be grounded before it is started up. A grounding cable is included with the pump. 1. lamp the grounding cable to the C terminal on the high pressure filter or the air motor. 2. onnect the other end of the grounding C cable to a suitable grounding device (e.g. grounding bar). PREPARING TO START UP THE BINKS PUMP Proceed as follows: 1. heck that the solvent cup C...

STARTUP AND OPERATION flows back into the tank through the high pressure filter, the high pressure ball valve and the return pipe. 6. emove the spray tip from the gun and R point the gun into the tank. Unlock the safety lever on the gun. Operate the gun trigger and close the high pressure ball valve (0114-019091). The spray material will now flow through the high pressure filter, the fluid hose and the gun, back into the tank. 7. elease the gun trigger and set the R working pressure at the regulator. NOTE Before carrying out any coating work, we recommend a test spray (e.g. on to paper or...

MX412 CART MOUNTED SYSTEMS PL = PTFE / Leather PP = PTFE PU = PTFE / UHMW UC = U-Cups 0 = none E = AA1600 Flat Tip F = AA1600 Twist Tip P = Airless 75 0 = none 1 = 100 mesh 2 = 200 mesh 0 = none S = 5 gallon T = 55 gallon 00 = none 25 = 25 ft / whip 50 = 50 ft / whip Ground wire System component List ITEM NO. PART NUMBER PART SHEET BARE PUMP ASSEMBLY (PTFE) BARE PUMP ASSEMBLY (PTFE/UHMW) BARE PUMP ASSEMBLY (PTFE/LEATHER) BARE PUMP ASSEMBLY (U-CUPS) AIRLESS 75 GUN ASSEMBLY MATERIAL HOSE (3/16" ID X 25', 1900 PSI) 1 IF GUN TYPE = P 1 IF HOSE LENGTH = 25 1 IF HOSE LENGTH = 50 1 IF HOSE LENGTH...

MX412 WALL MOUNTED SYSTEMS PL = PTFE / Leather PP = PTFE PU = PTFE / UHMW UC = U-Cups 0 = none E = AA1600 Flat Tip F = AA1600 Twist Tip P = Airless 75 0 = none 1 = 100 mesh 2 = 200 mesh 0 = none S = 5 gallon T = 55 gallon 00 = none 25 = 25 ft / whip 50 = 50 ft / whip Ground wire Ground wire System component List ITEM NO. PART NUMBER PART SHEET BARE PUMP ASSEMBLY (PTFE/LEATHER) BARE PUMP ASSEMBLY (PTFE) BARE PUMP ASSEMBLY (PTFE/UHMW) BARE PUMP ASSEMBLY (U-CUPS) SWIVEL ADAPTER (1/4" NPS M X F) [NOT SHOWN] ADAPTER FITTING (3/8" OD TUBE X 1/4" NPS F) DM NIPPLE (1/4" NPS/NPT X 3/8" NPS/NPT) 1 IF...

MX412 TRIPOD MOUNTED SYSTEMS PL = PTFE / Leather PP = PTFE PU = PTFE / UHMW UC = U-Cups 0 = none E = AA1600 Flat Tip F = AA1600 Twist Tip P = Airless 75 0 = none 1 = 100 mesh 2 = 200 mesh 0 = none S = 5 gallon T = 55 gallon 00 = none 25 = 25 ft / whip 50 = 50 ft / whip Ground wire System component List ITEM NO. DESCRIPTION BARE PUMP ASSEMBLY (PTFE/LEATHER) PART SHEET BARE PUMP ASSEMBLY (PTFE) BARE PUMP ASSEMBLY (PTFE/UHMW) BARE PUMP ASSEMBLY (U-CUPS) AIRLESS 75 GUN ASSEMBLY MATERIAL HOSE (3/16" ID X 25', 1900 PSI) 1 IF GUN TYPE = P 1 IF HOSE LENGTH = 25 SWIVEL ADAPTER (1/4" NPS M X F) [NOT...

MX412 LITE TRIPOD MOUNTED SYSTEM PARTS LIST ITEM NO. PART NUMBER MX412 BARE PUMP ASSEMBLY TUBE FITTING INLET FITTING SOCKET HEAD CAP SCREW

STAINLESS STEEL High Pressure Filter AssemblIES 0115-010326 (100 Mesh Filter Element) 0115-010630 (200 Mesh Filter Element) SPECIFICATIONS Max working pressure: Fluid inlet connection: Fluid outlet connection: Wetted parts materials of construction: 1/4" NPS (m) Stainless Steel, PTFE Additional filter mesh sizes (sold separately): For 50 mesh order: 0110-009131 For 150 mesh order: 0010-009133 PARTS LIST ITEM NO. 1 PART NUMBER 200 MESH FILTER ELEMENT 100 MESH FILTER ELEMENT FILTER HOUSING SWIVEL CONNECTING NIPPLE OUTLET SCREW OUTFLOW FITTING HIGH PRESSURE BALL VALVE HOSE CONNECTION FILTER...