L-1 Injector
6Pages

Product description Valve & dividers: Volumetric injector FL1 DESCRIPTION FL1 injectors are positive displacement type. They have adjustable outputs and a visual indicator pin. They can supply one lubrication point or several in combination with a progressive divider. All incorporate grease zerk fittings for priming of system. OPERATION The lubricant under pressure is introduced into entry port and pushes a seal which opens the entry channel. Pressure moves the main piston to deliver a preadjusted volume determined by the value of the discharge chamber. At the end of thelubrication cycle, the vent valve relieves the primary line. Spring which was compressed pushes the seal to its original position and opens the entry channel. When the main piston moves to the top, it transfers the lubricant into the discharge chamber. The injector is ready for the next cycle. (see system outline). Number of Reference 13844 13843 FL-1-1 FL-1-2 FL-1-3 FL-1-4 FL-1-5 FL-1-6 FL-1-8 1 2 3 4 5 6 8 1 /6 Dimensions A outlets System outline: mm inches mm Single injector with 3 / 8 NPT male adaptor Replacement injector for existing manifold 63 76 32 (1 1 / 4) 108 63 (2 1 / 2) 140 95 (3 3 / 4) 171 127 (5) 203 191 (7,5) 267 B inches (2 1 / 2) (3) (4 1 / 4) (5 1 / 2) (6 3 / 4) (8) (10,5) P_2009_1_GB_FL1

VENT VALVE REF 13850 and MINIATURE VENT VALVE REF 27926 Vent valve is used to relieve system pressure back to reservoir after a lubrication cycle. With a pneumatic operated pump, air pressure would be applied to the vent valve at the same time as the pump.When air pressure is relieved from pump and vent valve, lubricant moves past the valve seat and out vent port and piped back to the reservoir. Characteristics: Air pressure Lubricant pressure Mounting 3 /6 : : : 3 to 8 bars (40 to 129 PSI) 260 bar max (3800 PSI) any position P_2009_1_GB_FL1

INJECTOR COVER CAP REF U1732D Cover caps are used in environments where excessive moisture, dirt and other contaminants exist. They are intended to protect the internal components and the indicator pin to avoid lubricant leakages. Ref U1732D: Is made of clear vinyle plastic which allows visual check of indicator pin. Ref CAP13896A: Is made of aluminium to protect the injector head from high temperatures, up to 70°C. INJECTOR CONNECTOR TUBE REF 13899 Combines discharge of two or more injectors through one feed line or when a bearing lube requirement cannot be met from one injectors output. 4...

TABLE FOR DETERMINING RIGID LINE CAPACITIES AND SIZES Size of tube Ø3x4 Ø 8 x 10 Ø 10 x 12 Ø 13 x 15 Ø 16 x 20 3 / 4 " (20 x 27) 1 " (26 x 32) 1" 1 / 4 (33 x 42) 2 " (50 x 60) Grease NLGI 0 Primary line Secondary line 1,2 10 16 20 25 40 55 110 150 300 MAXIMUM LENGHT (METRE) Grease NLGI 1 Primary line Secondary line 1 5 8 8 12 20 30 55 80 200 Grease NLGI 2 Primary line Secondary line 2,5 5 8 12 20 30 50 120 Formula to determine section of tubing according to the lubricant using rigid pipe or flexible hose: 1. Determine the total length between pump and the farthest injector. 2. Coefficient...

BIJUR DELIMON Niederlassung Beierfeld United Kingdom Ramsden Court, Ramsden Road Rotherwas Industrial Estate BIJUR Lubricating Ireland Ltd. Gort Road Ennis, County Clare