CXL2 Injectors & Manifolds Premium Single Line Grease Systems General Designed for use in single line high pressure automatic grease systems, CXL2 Injectors deliver precise volumes of lubricant at predetermined intervals. Injectors are mounted in manifolds in close proximity to the points of lubrication. A wide selection of discharge rates, combined with a corrosion resistant finish, make this product ideally suited for mobile, wind and a broad selection of general industrial applications. Operation Lubricant introduced under pressure at the inlet moves the injector piston forward. The piston displaces a pre charge of lubricant from the discharge chamber through the outlet check valve and through the feed line. When system pressure is relieved, the piston returns to its rest position, transferring lubricant stored in the measuring chamber to the discharge chamber. The injector is then ready for the next discharge cycle. Rest Mode CXL2 Injectors – Double Row (shown assembled) Pressurized Mode OUTLET OUTLET INDICATOR INDICATOR PINPIN DISCHARGE DISCHARGE CAPCAP CHECK VALVE CHECK VALVE DISCHARGE DISCHARGE CHAMBER CHAMBER MEASURING MEASURING CHAMBER CHAMBER INJECTOR INJECTOR PISTON PISTON INLET INLET CXL2 Injectors – Single Row (shown assembled) Precise, dependable operation, no special tools required Visual indicator pin for inspection and troubleshooting Positive displacement output Easy to understand, install and service Single and double row configurations Injectors mount in any orientation Single supply line means lower installation cost Corrosion resistant for harsh environments BIJUR DELIMON INTERNATIONAL (919) 465 4448 LOCAL (800) 631 0168 TOLL-FREE (919) 465 0516 FAX WWW.BIJURDELIMON.COM 2250 Perimeter Park Dr., Suite 120 Morrisville, NC 27560

Technical Data Discharge/Cycle Lubricant Discharge Adjustment Discharge caps: 0.05cc – 0.40cc in 0.05cc increments available Minimum Operating Pressure Maximum Operating Pressure Minimum Vent Surface Protection Zinc Nickel, 1000-hour salt spray Carbon steel with surface protection Operating Temperature Range Manifold Inlet Ports Injector Outlet Tube Connection Option Female Thread Option 3/16” O.D. tube connection (standard) CXL2 Injectors – Single Row,Single Injector (shown assembled) 1/8” BSPP female connection 6mm O.D. tube connection Seals How to Order Individual Injectors & Manifolds Manifolds...

Service Parts Installation Note: Whenever inserting the piston and spring assembly into the injector body, the exposed end of the piston must be carefully started in the main bore and pushed in completely. If the assembly is forced, the piston and/or bore will be damaged and not function correctly. Part # 0.05cc (0.003 cu. in.) delivery 0.10cc (0.006 cu. in.) delivery Slide in piston and spring assembly Compression Sleeve * Do not overtighten, max torque 200 IN-LBS Correct installation BIJUR DELIMON INTERNATIONAL (919) 465 4448 LOCAL (800) 631 0168 TOLL-FREE (919) 465 0516 FAX WWW.BIJURDELIMON.COM...

Dimensional Schematics Manifolds Manifolds - Single NPT Manifolds - Single BSPP Manifolds - Double BSPP Manifold Description Manifold Description BIJUR DELIMON INTERNATIONAL Single Row & Double Row Manifolds WWW.BIJURDELIMON.COM 2250 Perimeter Park Dr., Suite 120 Morrisville, NC 27560

Overall Dimensions (for reference only) Measurements shown in millimeters. CXL2DXX 1/8" BSPP FEMALE CONNECTOR Single Row - Top and Bottom Dimensions 21 5.5 CXL2XXD 1/8" BSPP FEMALE CONNECTOR *NOTE: Injectors can be mounted position, up or down. Double Row - Top and Bottom Dimensions 5.5 BIJUR DELIMON INTERNATIONAL (919) 465 4448 LOCAL (800) 631 0168 TOLL-FREE (919) 465 0516 FAX WWW.BIJURDELIMON.COM 2250 Perimeter Park Dr., Suite 120 Morrisville, NC 27560