LubeSite 704 Grease, Metal Base, High Temperature General LubeSite 704 allows precise dispensing of grease to a bearing in ambient temperatures up to 450°F (232°C). It’s ideal for applications in steel mills, foundries, lumber drying kilns, glass plants, nuclear environments and metal heat-treating facilities. The refillable, transparent reservoir permits a visual inspection of grease level at a safe distance. This feature is especially important in high temperature applications. Application LubeSite 704 Series can be used on any equipment that has: ++ ++ ++ ++ Anti-friction oscillating, ball or roller bearings Shielded bearings with seals Bronze, oilite or open bearings Requires bearing flushing action See Brochure #L713: LubeSite Systems for more information Operation LubeSite automatic grease feeders have only two moving parts (spring, piston with metering rod and piston seal ring). The design combines foolproof simplicity with rugged component strength for dependable, controlled lubrication. The graduated channels in the meter rod allow the bearing to use grease as required. Once the reservoir is filled and the unit is connected to a bearing, the single-point lubricator uses Venturi action to discharge lubricant only when the bearing is in motion. Thus, grease is never packed into the bearing. This benefits manufacturers that will have some planned machine downtime, because over-lubrication is eliminated. Because the single-point lubricator only generates 1-5 psi it will not blow bearing seals. When the bearing stops, so does the grease flow. Technical Data Material Tempered borosilicate, glass Lightweight, anodized aluminum Stainless steel Thread Size Operating Temperature Note: These units are assembled with a medium (green) stainless steel spring. Units are packed individually and include an additional heavy (yellow) spring. The piston seal ring and gaskets are fabricated from temperature-resistant Viton. BIJUR DELIMON INTERNATIONAL (919) 465 4448 LOCAL (800) 631 0168 TOLL-FREE (919) 465 0516 FAX www.bijurdelimon.coM 2100 Gateway Centre Blvd., Suite 109 Morrisville, NC 27560

Start Up Instructions 1. Use proper spring: LubeSite 704 unit comes factory-equipped with medium spring (green) which gives correct grease feeding pressure for most applications. A heavyweight spring (yellow) is also supplied. 2. Remove grease fitting from equipment or bearing housing: Check to see that the thread on the grease fitting is 1/8”. You may need another LubeSite adapter to mount the LubeSite unit (refer to accessories). 3. Fill LubeSite unit with a non-separating grease: Connect a grease gun to the side grease fitting. Fill with grease until the grease comes out of the base coupler....

BUUR DELIMON Name Reservoir Capacity Parts When ordering, specify by name, description and part number, e.g. LubeSite 704, 4 oz Reservoir Name Description Material Parts Adapter Straight, 1/8" NPT (F) x 1/4"-28 (M) Zinc plated steel 20-1 Nickel chrome plated 50-1 Bushing, 1/8" NPT (F)x 1/4" NPT(M) Zinc plated steel 20-2 Nickel chrome plated 50-2 45°,l/8"NPT(F)xl/8"NPT(M) Zinc plated steel 20-3 Nickel chrome plated 50-3 45°l/8"NPT(F)xl/4"-28(M) Zinc plated steel 20-6 Nickel chrome plated 50-6 90°,l/8"NPT(F)xl/4"-28(M) Zinc plated steel 20-4 Nickel chrome plated 50-4 90°,l/8"NPT(F)xl/8"NPT(M) Zinc...

Dimensional Schematics Measurements shown in inches. BIJUR DELIMON INTERNATIONAL (919) 465 4448 LOCAL (800) 631 0168 TOLL-FREE (919) 465 0516 FAX www.bijurdelimon.coM 2100 Gateway Centre Blvd., Suite 109 Morrisville, NC 27560