*mydirectindustry

UPSIC-1205

Product catalog summary

Specifications:
The UPSIC-1205 is a 12 V DC uninterruptible power supply system with a nominal output current of 5 A and output power of 60 W. It features regulated voltage at backup, supercapacitors for energy storage, and is maintenance-free with high cycle stability exceeding 500,000 cycles. The charge time is less than 60 seconds at maximum charge current, and it operates within an extended temperature range of -20 to +70 °C. The design is compact and includes active reverse polarity protection. A power fail signal is available via relay and RS232 connection.

Electrical Parameters:
Input voltage ranges from 11.6 to 16 VDC with a nominal input current of 5.8 A. The output voltage in battery mode is 12 VDC ±2% regulated, while in normal mode it is Vin– 0.3 V at 100% load. The output ripple is ≤30 mV, and backup efficiency is 97% with supercapacitors at 9.5 V and output current at 2.5 A. The charging method is constant current/constant voltage (CC/CV), and the storage type is supercapacitors (4x 100 F).

Environmental Conditions:
The operating temperature range is -20 to +70 °C, and the storage conditions are the same. Operating humidity is 10–85% RH, non-condensing, and storage humidity is 10–90% RH, non-condensing.

Physical Dimensions:
The dimensions are 135 x 79.5 x 26 mm, including supercapacitors, and the net weight is 0.17 kg.

Additional Features:
The UPSIC-1205 includes a software UPS Control Center available for free download. It also supports various interface cables and optional accessories for enhanced connectivity and functionality.

Backup Time:
The backup time varies with output current, with a standby time of over 30 minutes at no load and nominal capacity at 25 °C.

Connectors and Interface:
The device includes connectors for input and output, as well as a CN J301 pin assignment for RS232 and I2C interfaces. LED indicators show charging state and power mode status.

Recommended Power Supplies:
Bicker Elektronik recommends power supplies such as BET-0912-T, BET-1012M, and BEN-10012, ranging from 90 to 100 Watts.

Catalog excerpts

Fanless Delivery Operation Extended 12 V DC / 5 A  Regulated voltage at backup  Supercaps for energy storage  Maintenance-free  High cycle stability > 500 000  Charge time <60 sec at maximum charge current  Extended temperature range -20…+70 °C  Compact design  Active reverse polarity protection  Power Fail signal via relay, RS232 connection  Intelligent charge sharing Te c h n i c a l d a t a Input voltage Input current Output power Output voltage battery mode Output voltage normal mode Output current Output ripple Backup efficiency Charge current Charging method Storage type Charging time Backup time Protection Temperature Humidity Dimensions (W x D x H) Weight (net) 12 VDC (11.6…16 V DC) 5.8 A nom. 60 W 12 VDC ±2 % regulated Vin– 0.3 V at 100 % load 5A ≤30 mV 97 % (VSupercaps 9.5 V, Iout 2.5 A) Depending on load up to 6.2 A CC (VSupercap) CC / CV Supercaps 4x 100 F <60 sec at maximum charge current @ 4x 100 F See diagram Overcurrent protection – Non LATCH Active reverse polarity protection Operating: -20…+70 °C / Storage: -20…+70 °C Operating: 10…85 % RH, non-condensing / Storage: 10…90 % RH, non-condensing 135 x 79.5 x 26 mm incl. supercaps @ 4x 100 F 0.17 kg @ 4x 100 F DC UPS Bicker Elektronik GmbH | 86609 Donauwö

Open the catalog to page 1

Optional Accessories [>[>[> For detailed information please visit our website www.bicker.de and refer to the article number. PSZ-1036 | Input cable 3-pole, length 500mm, AWG 18, ends open PSZ-1037 | Output cable 2-pole, length 500mm, AWG 18, ends open PSZ-1063 | ^Extension module pExtension module for DC2412-UPS(LD) -UPSIC-2403 - UPSIC-1205 PSZ-1046 / PSZ-1048 | Interface cable Interface cable for UPSIC and DC2412, PSZ-1046: IDC 2.0 to SUB-D 9 pin female, PSZ-1048: IDDC 2.0 to IDC 2.54 PSZ-1043 / PSZ-1044 | Interface cable For UPSIC and DC2412-UPS (-LD), PSZ-1043: TP connector wire open end,...

Open the catalog to page 2

UPS systems Backup time 180 sec. 170 sec. 160 sec. 150 sec. 140 sec. 130 sec. Application example with mITX Board IMB-154 (see parameters below) Backup time Output current Type 4x 100F: Standby @ No Load >30 min @ nom. Cap. & 25 °C Parameters of the test system for the backup curve Board RAM ROM OS Test Software Test results 1x mSATA 32 GB Type: CIE MSM300M JB032GS SN: CIE164905767 Microsoft Windows 10 Enterprise Evaluation Version 1511 Build 10586.589 (2016/09/16) BurnInTest V7.1 Pro 100 % load: 1 min. 43sec. = 103 sec Software UPS Control Center UPS Control Center The UPS software is available...

Open the catalog to page 3

UPS systems Drawing UPSIC-1205 Relay contact for Power Fail ^ Power Fail = 0 Ω 0.5 A @ 125 VAC 1 A @ 24 V DC I2C 10 SMB alert 11 GND 12 XSDA I²C 13 VOut 14 XSCL I²C RS232 01 DCD 02 DSR signal (Low = Cap >90 %; High = Cap <90 %) 03 NC 04 RTS signal (Supply voltage, max. 12 V) 05 NC 06 CTS signal (Low = Power Fail; High = Power OK) 07 NC 08 OD (Output Disable) 09 GND Connectors INPUT VHR-3N (1: 0V, 2: n.c., 3: V+) OUTPUT VHR-2N (1: V+, 2: 0V) CN J301 WR-BHD 62501021621 (pitch 2.0 mm) RELAY WR-691210910002 LED D302 RED Caps charging state < 90% D301 RED Power fail, backup mode D201 GREEN Normal...

Open the catalog to page 4

UPS systems Interface schematic J301 J301, PIN1 (DCD ON PC OR HOST) CABLE CONNECTED R346 4k7 J301, PIN4 (RTS ON PC OR HOST) USED AS SUPPLY J301, PIN2 (DSR PC OR HOST) CAPS CHANGE STATE High CAP<90% J301, PIN6 (CTS ON PC OR HOST) Power Fail Low Internal connection Power Fail High Low CAP <90% Internal connection High CAP >90% or Full Charged Specification is subject to change without notice. Errors excepted. Status as at: 03.07.2018 Recommended power supplies from Bicker Elektronik  Additional recommendations on www.bicker.de BET-0912-T BET-1012M BEN-10012 90 Watt 100 Watt 100 Watt Bicker...

Open the catalog to page 5