UPSI-2406
3Pages

Catalog excerpts

Fanless Delivery 24 V DC / 6 A  24V DC UPS (Open frame PCB version)  Intelligent power sharing  Regulated output voltage  Min. load disconnect  Battery disconnect  Power fail timer  Battery start function  External signal shutdown  Battery hot swap  Reboot function  Fuel gauge Also available as DIN Rail version UPSI-2406D Product specific data Battery monitoring Shutdown detection Reboot function Load sensor Timer function External signal shutdown Backup time Relay 24 V DC (22.5…29 V) 7.5 A max. Normal mode: Vin– 0.3 V (Full load) Backup: 23.5 V DC 6 A max. 3000 µF (24 V Startup) 3 A max. on input CC / CV / CP Deep discharge protection Overcurrent protection Reverse polarity protection USB, RS232, USB-HID LiFePO4, Supercaps Operating: -20…+70 °C / Storage: -20…+70 °C Backup mode: +55…+70 °C, 100 mA (2.35 W) / °C 5000 m 1500 m operation altitude or higher: 5.7 W / 500 m or reduction of operation temperature of 3.5 °C / 500 m Operating: 10…85 % RH, non-condensing / Storage: 10…90 % RH, non-condensing 105 x 68 x 17 mm ±0.5 mm 0.09 kg Battery test is executed in normal mode Via load sensor Reboot function and time can be configured by software Configurable via UPSI HID-Battery-Parameter software (download at www.bicker.de) UPS shuts down after 15 sec, if connected load decreases below set value and UPS is being in battery mode Configurable via UPSI HID-Battery-Parameter software in steps of single seconds (3600 sec max) UPS can be configured to shut down on external signal (e.g. ignition) with delay set in steps of single seconds (3600 sec max) See datasheets of battery packs Dry contact on power fail (Normal mode: open / Backup mode: closed) Relay switching current max 0.5 A @ 125 V AC / 1 A @ 24 V DC As a power component this UPS is for assembly purposes only and must not be operated in unassembled condition. The final assembly has to comply with the valid EMC and safety standards. Bicker Elektronik GmbH | 86609 Donauwörth | Germany Tel. +49 906 70595-0 | info@bicker.de | www.bicker.de Input voltage Input current Output voltage Output current Capacitive Load Battery charge current nom. Charging method Protection Interface Type of battery Temperature Derating (depending on temperature) Max. operation altitude Derating (depend

Open the catalog to page 1

UPS systems Drawing UPSI-2406 Tolerance ±0.5 mm X10 1 XPF# 2 GPIO / I²C 3 GND 4 GPIO / I²C 5 5 V DC supply (max 50 mA) 6 ANLG-R input, Alternative Power Fail Timer / 30 V max Description Part No. Vin / Vout WE 691325310004 LED pin header Battery pack power WE 64900429522 I2C and SP to battery pack WE 62400821722 Relais WE 691305140002 USB WE 61400416121 USB Pin header 2.54 mm WE 61300511121 JTAG Pin header 1.27 mm WE 62101021021 RS232 WE 690367281076 System info (+5 V DC, PF#, 2x Dig. I/O, ANLG-R) WE 690367280676 Pin header – cold start Reset button Jumper WE 62000211121 Bicker...

Open the catalog to page 2

UPS systems Battery packs and Backup time for UPSI-2406 Nominal backup time, measured at +21 °C 50 W BP-LFP-1325 ~ 33 min BP-LFP-1375 ~ 99 min BP-SUC-1615 ~ 29 sec BP-SUC-1645 ~ 95 sec BP-SUC-2120 ~ 39 sec BP-SUC-16090 ~ 190 sec Back up time depends on battery capacitance, load and temperature. At very high or low temperatures a reduction of backup time occurs. Larger capacities on request P/N explanation battery packs BP – XXX – YYZZ Battery Pack LFP = LiFePO4 YY Approx. nom. V SUC = Supercaps ZZ Capacitance (LiFePO4 in 10-1 Ah) or useful energy (Supercaps in 10-1 kJ) Example: BP-LFP-1325...

Open the catalog to page 3

UPSI-2406 3Pages

Catalog excerpts

All Bicker Elektronik GmbH catalogs and technical brochures

UPSI-2406
3Pages