Fanless Delivery 12 V DC / 8 A  12V DC UPS (Open frame PCB version)  Intelligent power sharing  Regulated output voltage  Min. load disconnect  Battery disconnect  Power fail timer  Battery start function  External signal shutdown  Battery hot swap  Reboot function  Fuel gauge Also available as DIN Rail version UPSI-1208D Product specific data Battery monitoring Shutdown detection Reboot function Load sensor Timer function External signal shutdown Backup time Relay 12 V DC (11.5…16 V) 9.5 A max. Normal mode: Vin– 0.3 V (Full load) Backup: 12 V DC 8 A max. 4700 µF (12 V Startup) 4 A max. on input CC / CV / CP Deep discharge protection Overcurrent protection Reverse polarity protection USB, RS232, USB-HID LiFePO4, Supercaps Operating: -20…+70 °C / Storage: -20…+70 °C 5000 m 1500 m operation altitude or higher: 3.5 W / 500 m or reduction of operation temperature of 3.5 °C / 500 m Operating: 10…85 % RH, non-condensing / Storage: 10…90 % RH, non-condensing 105 x 68 x 17 mm ±0.5 mm 0.09 kg Battery test is executed in normal mode Via load sensor Reboot function and time can be configured by software Configurable via UPSI HID-Battery-Parameter software (download at www.bicker.de) UPS shuts down after 15 sec, if connected load decreases below set value and UPS is being in battery mode Configurable via UPSI HID-Battery-Parameter software in steps of single seconds (3600 sec max) UPS can be configured to shut down on external signal (e.g. ignition) with delay set in steps of single seconds (3600 sec max) See datasheets of battery packs Dry contact on power fail (Normal mode: open / Backup mode: closed) Relay switching current max 0.5 A @ 125 V AC / 1 A @ 24 V DC As a power component this UPS is for assembly purposes only and must not be operated in unassembled condition. The final assembly has to comply with the valid EMC and safety standards. Bicker Elektronik GmbH | 86609 Donauwörth | Germany Tel.   +49 906 70595-0 | [email protected] |  www.bicker.de Input voltage Input current Output voltage Output current Capacitive Load Battery charge current nom. Charging method Protection Interface Type of battery Temperature Max. operation altitude Derating (depending on

X10 1 XPF# 2 gpio / Pc 3 GND 4 GPIO / PC 5 5 V DC supply (max 50 mA) 6 ANLG-R input, Alternative Power Fail Timer / 30 V max Connection Connector Description Vin / Vout LED pin header Battery pack power I2C and SP to battery pack Relais USB USB Pin header 2.54 mm JTAG Pin header 1.27 mm RS232 DC UPS System info (+5 V DC, PF#, 2x Dig. I/O, ANLG-R) WE 690367280676 Pin header - cold start Reset button Jumper WE 62000211121 Bicker Elektronik GmbH | 86609 Donauworth | Germany Tel. +49 906 70595-0 | [email protected] | www.bicker.de

Battery packs and Backup time for UPSI-1208 Nominal backup time, measured at +21 °C 50 W 100 W 140 W Back up time depends on battery capacitance, load and temperature. At very high or low temperatures a reduction of backup time occurs. Larger capacities on request. P/N explanation battery packs Battery Pack LFP = LiFePO4 YY Approx. nom. V SUC = Supercaps ZZ Capacitance (LiFePO4 in 10-1 Ah) or useful energy (Supercaps in 10-1 kJ) Example: BP-LFP-1025 BP Battery Pack LFP Storage medium: LiFePO4 Quantity Description Specification is subject to change without notice. Errors excepted. Status as at:...