Industrial PC power suppl' © ATX DC/DC converter © Ultra wide input range 6...36 VDC © Extended temperature range -20...+70 °C © Efficiency up to 93 % © With motor vehicle ignition function © No minimum load required © Cable management system © High quality components provide maximum reliability and a long life time © POWER_ON and POWER_OK meets Intel® ATX 12 V design guide requirements Technical data Input voltage Input current Inrush current Efficiency Standby consumption Power-Good-Signal Protection Insulation voltage Temperature Derating MTBF Humidity Dimensions (W x D x H) Weight (net) 24 V DC (6...36 V DC) Max. 7.2 A (24 VDC) 20 A max. (24 VDC) App. 93 % <1 W Switch on delay 100.500 ms / Switch off delay 3.5 ms Input: Inverse-polarity protection Output: Short circuit protection: +3.3 V, +5 V, +12 V, -12 V, 5 Vsb Overvoltage protection: +3.3 V, +5 V, +12 V, -12 V, 5 Vsb Overtemperature protection: Depends on ambient temp., load and cooling No separation between input / output Operating: -20...+70 °C / Storage: -20...+85 °C See diagrams App. 990 000 h according to Telcordia SR-332 at +50 °C Operating: 10.90 % RH, non-condensing / Storage: 10.95 % RH, non-condensing 160 x 45 x 24 mm ±0.5 mm 0.18 kg Article Output Output current Load Ripple & No. voltage min max peak regulation Noise Max. output power is 160 W with connection to heatsink/metal housing (thermal resistance: <6K/W) and 100 W with free mounting (24 V /<55 °C). All measurements were performed with an aluminum heat sink (180x55x 3 mm) and heat transfer pad (included) at 25 °C. At input voltages 6...10 V and/or temperatures >55 ° C both diagrams must be considered. Peak output current can be for max.. 1 sec within 1 minute. No galvanic isolation! Ripple and noise was measured by a 20 MHz bandwidth limited oscilloscope with connected 10 jut and 0.1 jut capacitors at each output. This unit is for assembly purposes only and it must not be operated in unassembled conditionThe final assembly has to comply with the valid EMC standards. Bicker Elektronik GmbH | 86609 Donauworth | Germany Tel. +49 906 70595-0 | [email protected] | www.bicker.de

Industrial PC power supplies Optional Accessories   detailed information please visit our website www.bicker.de and refer to the article number. For CB-DC120W-P4 | P4 cable Length 350 mm, max. 5 A, thread plug, 5.5 x 2.5 mm Reduces conducted noise and emission Bicker Elektronik GmbH | 86609 Donauwörth | Germany Tel.   +49 906 70595-0 | [email protected] |  www.bicker.de

Industrial PC power supplies Derating DC input Input voltage derating Output power — Derating at convection cooling and connection to heat sink or metal housing with thermal resistance of < 6K/W — Derating at convection cooling and free mounting Temperature derating Output power* *Percentage refers to power of input voltage derating Bicker Elektronik GmbH | 86609 Donauwörth | Germany Tel.   +49 906 70595-0 | info@b

Industrial PC power suppl'Drawing DC161W Tolerance: ±0.5 mm The following modes for ignition functions are selectable by jumper: J4 Jumper attached^ © 5 Vsb Hard-off: In case battery voltage falls below the listed„Switch Off" voltage for 1 minute or longer, the DC 161 W automatically shuts down (deep discharge protection): Mode P1-P10 Switch Off @ 11.0 V - Start @ 12.0 V Mode P11-P12 Switch Off @ 10.5 V - Start @ 10.8 V Mode P13-P14 Switch Off @ 10.7 V - Start @ 11.3 V Switch Off @: Separation of the application from 5Vsb during the Hard-off time when the voltage drops below the specified value...

Industrial PC power supplies In case of a temperature transfer of the PCB to the chassis bottom via heat transfer pad (included in delivery) the PCB temperature decreases depending on the ambient temperature. For details see derating diagram.  SPECIAL DESIGN We are glad to assemble for you special requests such as Phoenix Contact connectors or individual wire harness. Contact us! Specification is subject to change without notice. Errors excepted. Status as at: 17.02.2020 For fixed soldered wire harness, see our model DC160W. Contact us! Bicker Elektronik GmbH | 86609 Donauwörth | Germany Tel.   +49...