*mydirectindustry

DC1224

Product catalog summary

Specifications:
The DC1224 is a 100 Watt DC/DC converter that converts 12 V to 24 V. It features a very small size and a chassis designed for electric shock protection and heat dissipation. The output voltage is +24 V with a minimum current of 0 A and a maximum of 4.1 A, peaking at 8 A. Load regulation is ±5% with a ripple and noise of 240 mV. The input voltage range is 11.2 to 13.4 V DC, with a maximum input current of 11 A. Efficiency ranges from 91% to 94% at nominal load.

Protection and Insulation:
The converter includes short circuit protection that switches off and overload protection between 120% and 150%. There is no separation between input and output for insulation voltage.

Environmental Conditions:
Operating temperature ranges from -10°C to +60°C, with storage temperatures from -25°C to +85°C. Derating occurs between +50°C and +60°C at 2.5% per °C. The maximum operation altitude is 3000 m, and humidity ranges from 10% to 85% RH for operation and 10% to 90% RH for storage, both non-condensing.

Physical Characteristics:
The dimensions are 31.2 x 99 x 20 mm with a tolerance of ±0.5 mm, and the net weight is 0.08 kg.

Performance and Usage:
The converter provides a regulated 24 V DC output with high efficiency up to 94%. It is designed for demanding industrial and medical applications, using high-quality components like polymer aluminum capacitors for reliability. The maximum output power should not exceed 100 Watts. Ripple and noise measurements were taken with a 20 MHz bandwidth limited oscilloscope and 0.1 µF capacitors at each output. An additional input filter may be necessary for low voltage systems. Peak output current is sustainable for a maximum of 5 seconds, with a recovery time of at least 10 seconds.

Assembly and Compliance:
This power supply unit is intended for assembly purposes only and must not be operated unassembled. The final assembly must comply with EMC and safety standards.

Connectors:
Connector CN1 input uses Molex 39-01-2040 or identical, with PIN 3 and 4 (yellow) as IN+ and PIN 1 and 2 (black) as IN-. Connector CN2 output uses Molex 39-01-4020 or identical, with the left as yellow OUT+ and the right as black OUT-.

Optional Accessories:
Available accessories include connectors with cables, such as the CB-103-4-280 and CB-104-2-300, with varying lengths and configurations.

Catalog excerpts

DC1224 100 Watt □ DC/DC converter 12 V to 24 V □ Very small size □ Chassis for electric shock protection & heat dissipation The DC/DC converter generates a regulated output voltage of 24 V DC and is characterized by its particular small size and its high efficiency of up to 94 %. To achieve a good thermal management, the power modules are installed on the bottom side. The high quality components, e.g. polymer aluminium capacitors, provide maximum reliability while operating in demanding industrial and medical applications. Technical data Input voltage Input current Efficiency Protection Insulation voltage Temperature Derating Max. operation altitude Humidity Dimensions (W x D x H) Weight (net) 12 VDC (11.2.. .13.4 V DC) 11 A max. 91.94 % (at nominal load) Short circuit protection: Switch off Overload protection: 120.150 % No separation between input and output Operating: -10.+60 °C / Storage: -25.. .+85 °C +50.+60 °C, 2,5 % / °C 3000 m Operating: 10.85 % RH, non-condensing / Storage: 10.90 % RH, non-condensing 31.2 x 99 x 20 mm ±0.5 mm 0.08 kg Maximale Output power must not exceed 100 Watt. Ripple and Noise was measured by a 20 MHz bandwidth limited oscilloscope with connected 0.1 yF capacitors at each output. Connecting to a low voltage system an additional input filter could be necessary. Peak output current can be for max. 5 sec. The recovery time after the peak current should be at least 10 sec. As a power component this PSU is for assembly purposes only and must not be operated in unassembled condition. The final assembly has to comply with the valid EMC and safety standards. Bicker Elektronik GmbH | 86609 Donauworth | Germany Tel. +49 906 70595-0 | [email protected] | www.bicker.de

Open the catalog to page 1

DC/DC converters Specification is subject to change without notice. Errors excepted. Status as at: 21.12.2015 CN2: Left: yellow OUT+ Right: black OUT– Connector: Connector CN1 input: Molex 39-01-2040 or identical Connector CN2 output: Molex 39-01-4020 or identical Optional accessory Article No. CB-103-4-280 CB-104-2-300  detailed information please visit our website www.bicker.de and refer to the article number. For Description P4 connector with 4 cables (2x black, 2x yellow), length 280 mm, ends open 2-pole connector with 2 cables (black, yellow), length 300 mm, ends open Bicker Elektronik GmbH...

Open the catalog to page 2