Bezares Group

Introduction General Information: BH* & V* General Information: DT6/7* Single Vane Pumps BH*, V* and DT6/7* single vane pumps Thru Drive Single Vane Pumps V**T thru drive single vane pumps Double Vane Pumps V* and DT6* double vane pumps Triple Vane Pumps DT6* triple vane pumps Single and Double Vane Pumps 4 holes ISO Flange T6GC and T6GCC for direct mounting in Power Take Off Single Vane Pumps With Flow Control and Priority Valve. Vane Motors MD4C & MH4D Motors USE, MAINTENANCE AND REPAIR GUIDE Description and Maintenace Real Images of Common Failures Pump start-up. Identification. Assembly &...

TDZ Hydraulics introduce the most complete line of fixed displacement vane pumps, both for mobile and industrial applications. Hydraulically balanced, our pumps offer low noise level and high volumetric efficiency. Flows: Single pumps: 2 cm3 up to 270 cm3, (0,6 up to 85 gallons). Double pumps: 10+10 cm3 up to 270+190 cm3, (6+1 up to 85+61 gallons). Triple pumps: 48+10+10 cm3 to 270+191+100 cm3, (14+3+3 gal. up to 85+61+30 gal.) Maximum pressure: 210 bar, (3.000 p.s.i.), in VK, VS, VQ series 280 bar, (4.000 p.s.i.) in DT6 series. TDZ Hydraulics stellt das vollständigste Programm von Flügelzellenpumpen...

Vane Pumps & motors

SINGLE, DOUBLE & TRIPLE VANE PUMPS BH*, V* & DT6 HYDRAULIC VANE PUMPS All TDZ pumps have a low power to weight ratio, high efficiency, low noise levels, optional inlet and outlet port positions and ease of maintenance. Ease of maintenance is achieved by the pump design, where the working components are contained within a cartridge which can quickly and easily be replaced without disconnecting the pump from the prime mover or moving it away from the pipe work. TDZ vane pumps are hydraulically balanced, reducing wear and eliminating bearing loads from within the pump. The option to rotate the outlet...

SINGLE, DOUBLE & TRIPLE VANE PUMPS V* & BH* HYDRAULIC VANE PUMPS DATA SHEET INTRODUCTION PUMP DRIVE Direct coaxial drive is recommended via flexible coupling. For indirect drives imposing a radial load on the shaft, consult TDZ or your nearest distributor for advice. ROTATION The direction of rotation can be reversed by turning the ring, rotor and vanes through 180degrees. Direction of rotation is viewed from the shaft end. STARTING TDZ vane pumps are self priming, however, if possible, fill the pump with oil before starting or bleed the outlet port while the pump is running to remove any trapped...

SINGLE, DOUBLE & TRIPLE VANE PUMPS V* & BH* HYDRAULIC VANE PUMPS DATA SHEET INTRODUCTION MAXIMUM CONSTANT PRESSURE Anti-wear Hydraulic Oil: from 175 to 210 Bar Synthetic Oil: from 175 to 210 Bar Water-Glycol emulsions: 160 Bar Water-in-oil emulsions: 70 Bar SOUND LEVEL Single Pumps: VS25 and BHS4: 62 dB (A) VS35 and BHS6: 65 dB (A) VS45 and BHS7: 71 dB (A) Double Pumps: VS43: 68 dB (A) VS63: 69 dB (A) VS73: 71 dB (A) VS64: 69 dB (A) VS74: 71 dB (A) VS76: 72 dB (A) Sound levels measured with hydraulic oil at 140 Bar, 1500 rpm and a vacuum at pump inlet of 0,17 Bar. ADMISSIBLE TORQUES FOR...

Bezares Group SINGLE, DOUBLE & TRIPLE VANE PUMPSDT6/7 HYDRAULIC VANE PUMPS DATA SHEET INTRODUCTION DT series vane pumps are fixed displacement and high efficiency pumps. Designed under SAE J744c 2 bolt standards, (excluding T6EDC triple pumps), the complete range includes single, double and triple units with wide possibilities of flow combinations, porting configurations, possibilities of use of fluids other than petroleum-based oil and a vast number of different shafts. The DT series is a hydraulically-balanced design. Quality and composition of materials have been checked and tested over millions of...

SINGLE, DOUBLE & TRIPLE VANE PUMPS DT6/7 HYDRAULIC VANE PUMPS INTRODUCTION Operating characteristics showed in this catalogue have been calculated considering the use of Antiwear petroleum base fluids. Non Antiwear Petroleum Base Fluids, Synthetic Fluids, Water In Oil Emulsions or Water Glycols are also acceptable. In these cases, speed and pressure limits will be supplied directly by TDZ Hydraulics or your nearest distributor. VISCOSITY Optimum viscosity for maximum life is between 30 and 40cSt. Maximum viscosity is 2000 cSt at very low speed and pressure and 110 cSt at full speed and pressure....

DATA SHEET SINGLE VANE PUMPS BH*, V* and DT6/7 single vane pumps

BH* SINGLE VANE PUMPS DATA SHEET Bezares Group 1- "F3" means special seals for fire-resistant fluids. Omit if not required. 2- Pump Type: BHP = 10 vane pump, industrial and mobile use, BSP, NPT & SAE threads. Only BHP1 and BHP2 BHS = 12 vane pump, industrial use (very quiet),metric threads. BHQ = 10 vane pump and bronze plates, mobile use, metric threads. 3- Pump model: 1and 2 in BHP types; 4,6 and 7 in BHS and BHQ types. 4- Flow: BHP ,BHS and BHQ in Litres per minute at 1000 rpm and 7 Bar. 5- D = Right - hand direction of rotation (Clockwise). Y = Left - hand direction of rotation. (Counterclockwise). (To...

BH* SINGLE VANE PUMPS Bezares Group TDZ DESIGN VANE PUMPS DATA SHEET *27 gallons (88 Its.) cartridge not mounted in BHQ4 vane pump model. (1) Delivery flow reduction in Ltrs./min. at 100 Bar. 22 cST of oil viscosity at operating temperature. To calculate the approximate delivery flow at a given pressure and speed, use the following formula with flow reduction and theoretical flow values shown in the chart. Flow reduction values are independent of shaft speed. Approx. output flow (Ltrs./min.) = Theoretical flow x - Reduction x Pressure (Bar) (2) Nominal Power in H.P. at 100 Bar and 1000 RPM...

BH* SINGLE VANE PUMPS Bezares Group

Bezares Group SINGLE VANE PUMP TYPE BHP-1 BH* SINGLE VANE PUMPS

BH* SINGLE VANE PUMPS Bezares Group * For further details see general chart

BH* SINGLE VANE PUMPS SINGLE VANE PUMP TYPE BHP-2 DATA SHEET FLOW AND INPUT POWER DIAGRAMS

BH* SINGLE VANE PUMPS DATA SHEET Bezares Group SINGLE VANE PUMP TYPE BHS-4 & BHQ-4 * For further details see general chart DIMENSIONS IN MILLIMETERS 1" = 25.4 mm Enquire about other types of shafts