*mydirectindustry

PF/9110 7040 7016

Product catalog summary

Description: The UHS Primer Filler PF/ is designed for car refinishing, offering high hiding power, easy application, and fast sandability. It adheres to various surfaces including steel, aluminum, galvanized materials, GRP, PP-EPDM, and ABS.

Colors: By mixing the three base colors (PF/9110, PF/7040, PF/7016), different shades of gray can be achieved to enhance the hiding power for the W6000 series colors.

Surface Preparation: Before repair, surfaces should be sanded, cleaned, and degreased using SO/1020-SO/4020. For plastic surfaces not covered in the data sheet, apply the plastic addition promoter SP/1895 first.

Application Instructions: Apply a fine, uniform layer to avoid high film thickness, which can delay the process or cause shrinkage. Leave 5 minutes between layers or until the surface is matt. The mixing ratio varies with different hardeners (HA/8010 to HA/8070) and the application involves 1-3 coats with a thickness of 75-100 mµ. Drying times vary based on temperature and hardener used.

Finish: Sanding should be done with P320 to P400 after drying and cooling. The product is suitable for flexible or semi-flexible plastic supports with the addition of 5% SINNEK PL/7078 additive.

Storage: Store in a dry, ventilated place, avoiding direct sunlight, at temperatures above 5ºC, ideally between 15-30ºC.

Safety and Hygiene: Use appropriate personal protective equipment to prevent irritation. The product is for professional use only and complies with European Norm 2004/42/CE II(C) with VOC content <540 g/l.

Catalog excerpts

TECHNICAL SHEET DESCRIPTION PF/ is a UHS primer designed for car refinish. It stands out for its high hiding power, easy application and fast sandability. Adhesion on: steel, aluminum, galvanized, GRP, PP-EPDM, ABS. COLORS Mixing the 3 base colors of the PF range you can achieve different shades of gray for a right hiding power of each of the colors of the W6000 series. SURFACE PREPARATION Before starting with the repair, sand, clean and degrease correctly with degreaser SO/1020-SO/4020. Recoatable with the W6000 Series. On plastic surfaces not included on this technical data sheet, first apply the plastic addition promoter SP/1895. APPLICATION INSTRUCTIONS Leave 5 minutes between layers or until matt surface. Avoid high film thickness to prevent delays in the process or shrinkage in the finish coat. Apply a fine and uniform layer facilitating a finish of the painting system with excellent levelling and sharpness.

Open the catalog to page 1

TECHNICAL SHEET PF/9110 7040 7016 UHS PRIMER FILLER APPLICATION 1 Mixing ratio Mixing ratio Application FORD PF/ 9110-7040-7016 HA/8010 Slow HA/8020 Medium HA/8030 Fast HA/8040 Extra-Fast PF/ 9110-7040-7016 HA/8045 Slow HA/8055 Medium HA/8065 Fast HA/8070 Extra-Fast Gravity spraygun Application pressure Thinner evaporation time Drying time 20ºC (to manipulate) IR Middle wave 60ºC 5´-10´ before force drying ATTENTION: In the case of flexible or semi-flexible plastic supports, it is possible to add 5% of SINNEK PL / 7078 additive on component A. The proportions of hardener and thinners remain the...

Open the catalog to page 2

TECHNICAL SHEET SAFETY AND HYGIENE Recommendable to use the appropriate personal protective equipment during application to avoid irritation of breathing tract, skin and eye irritation. For professional use only. STORAGE Keep covered in a dry and ventilated place, avoiding direct exposure to sunlight. We advise Temperature above 5ºC, recommended between 15-30ºC. VOC PF/ has a lower organic solvent content than the traditional, compliant with the European Norm 2004/42/CE II(C) (540) <540 g/l The information contained in this Technical Data Sheet is based on our knowledge and experience and with...

Open the catalog to page 3

PF/9110 7040 7016

PF/9110 7040 7016

Catalog excerpts

All Bernardo Ecenarro, S.A. SINNEK catalogs and technical brochures