Series X
64Pages

with you at every turn Series X Flexible Couplings

Serving an entire spectrum of mechanical drive applications from food, energy, mining and metal; to automotive, aerospace and marine propulsion, we are here to make a positive difference to the supply of drive solutions. Worm Gear units reduction types Parallel angle helical bevel helical geared motors & reducers Right angle helical bevel helical geared motors & reducers Screwjack worm gear unit Helical parallel shaft & bevel helical right angle drive gear In-line helical geared motors & reducers Worm gear unit Large helical parallel shaft & bevel helical right angle drive units Roloid Gear...

ATEX Compliance Assured Total compliance with the ATEX Directive safeguarding the use of industrial equipment in potentially explosive atmospheres is assured for users of our geared products. Certification is available for standard gearboxes and geared motors with badging displaying the CE Mark and the Ex mark, name and location of the manufacturer, designation of series or type, serial number, year of manufacture, Ex symbol and equipment group/category. ATEX directive 94/9/EC (also known as ATEX 95 or ATEX 100A) and the CE Marking Directive are enforced in all EC member states. Compliance...

CONTENTS PAGE General Information / Reference Notes. Selection Procedure_ General Description. Unit Designations_ Dimensions & Specifications Type GC05 Floating Shaft Assembly. Type G52 Floating Shaft Assembly. G Mill Motor & Taper Bores GF Mill Motor & Taper Bores. 12 Recommended Keys for Shaft - Metric and Inch_28 Motor Shafts and Ratings - Metric and Inch-28 General Description. Unit Designations_ Dimensions & Specifications Type T50 Floating Shaft Assembly. Taper Lock Bushings_ 34 Recommended Bores - Metric and Inch. Misalignment Capacities- CONE RING General Description. Unit...

GENERAL INFORMATION REFERENCE NOTES General Information Inch/Metric conversions may not be direct conversions. - Our standards apply unless otherwise specified. - All Dimensions are for reference only and are subject to change without notice unless certified. - Unless otherwise specified, our coupling hubs will be bored for CLEARANCE FIT with a setscrew OVER the keyway or INTERFERENCE FIT without a setscrew. - Torque ratings of couplings utilising Taper-Lock bushings can differ from those that do not. Referto our Application - If we are to supply coupling hubs bored for Taper-Lock bushings,...

SELECTION PROCEDURE Standard Selection Method The standard selection method can be used for most motor, turbine, or engine driven applications. The following information is required to select a gear coupling. Application or type of equipment to be connected (motorio pump, drive to conveyor, etc.). Shaft diameters. Shaft gaps. Physical space limitations. Special bore or finish information and type of fit. Exceptions are High Peak Loads and Brake Applications. For these conditions, use the Formula Selection Method in the next column, or consult one of our Application 1. RATING: Determine...

SELECTION PROCEDURE Table 1 - Coupling Service Factors for Motor ♦ and Turbine Drives Alphabetical listing of applications Alphabetical listing of applications Direct Connected.. Referto Application Engineer Without Flywheel.. Refer to Application Engineer With Flywheel and Gear between Compressor and Prime Mover 0 4 or more cyl., double acting ... 1,75 Apron, Assembly, Belt, Chain Live Roll, Shaker and Forced Draft - Across the Forced Draft Motor Driven thru Induced Draft with damper For engine drives, refer to Table 2. Electric notors, generators, engines, compressors and ulhei...

SELECTION PROCEDURE SERVICE FACTORS: are a guide, based on experience of the ratio between coupling catalogue rating and system The system characteristics are best measured with a torque Table 3 . Service Factors The following information is necessary to quote or ship to your characteristics, exact requirements. Prompt service is assured if this information is given on your inquiry or order. 1. Application: Driver & Driven 2. Power: Normal kW, Maximum kW or Torque (Nm) 5. Coupling Size and Type, 6. Shaft Gap or distance between shaft ends (BE Dimension) 7. Bore Sizes: Must Specify clearance...

Torsionally rigid, high torque couplings

GEAR COUPLINGS Gear Couplings Atorsionally rigid, lubricated design that offers high torque capacity, application versatility, and where high torque loads exist or shaft diameters exceed 100 mm, the lowest initial cost. Available in 28 sizes, and all featuring triple-crowned teeth, our gear couplings offer the highest torque ratings (over 8 million Nm) and the largest bore capacities (up to 1025 mm) in the industry. Continuous Sleeve Couplings profile sleeve encompassing the hubs. Economical and compact. Available in both close coupled and floating shaft models, (see applications, provide...

GENERAL DESCRIPTION Gear Couplings Low Initial Cost. Highest Bore Capacities & Ratings. The wrong gear coupling can be costly. So we have developed the less expensive solution: Series X Type G couplings. The low initial cost of Gear Couplings, along with the highest bore capacities and ratings make them the true money saving option saving you as much as 35 percent over competitive designs. Built to last longer, protect your equipment and save you money, our gear couplings are right for a whole world of What's more, our couplings are designed to AGMA size standards, and are interchangeable...

UNIT DESIGNATIONS Gear - Continuous Sleeve GC05 = Single Engagement/Floating Shaft Gear - Standard Flanged Sleeve Type (Shrouded and Exposed Bolts) : Double Engagement (Shrouded /Exposed) : Single Engagement / Floating Shaft (Shrouded /Exposed) : Vertical Double Engagement (Shrouded / Exposed) : Vert. Single Engage. / Floating Shaft (Shrouded /Exposed) : Brakewheel Double Engagement (Exposed) : Disc Brake Double Engagement (Exposed) : Brakewheel Single Engagement (Exposed) : Slide Double Engagement (Exposed) : Slide Single Engagement / Floating Shaft (Exposed) : Disconnect / Inching Drives...