CASE STUDY Project Summary Organization: Sabesp MA Solution: Water and Wastewater WaterCAD Helps Sabesp Identify Optimal Hydraulic Strategy, Solving Water Supply Issues Location: São Paulo, Brazil Hydraulic Modeling Project Provides Continuous Water Supply to 240,000 Inhabitants While Reducing Operating Costs by BRL 700,000 Project Objective: • Provide continuous water supply to 240,000 inhabitants, even during power outages. Power Outages and Safety Issues Hinder Water Supply • Identify a solution that is hydraulically performant, while reducing operation costs Products used: WaterCAD Fast Facts • Power outages caused pump shutdowns that when occurring during the night could not be addressed by Sabesp personnel for safety reasons, leaving 240,000 people with no potable water during that time. • The initial solution considered would have increased operating costs. Sabesp MA is a mixed-capital company that provides water and sewage services to the 364 municipalities in the state of São Paulo, Brazil. It is considered one of the largest water and sewage service providers in the world, supplying potable water to 27.7 million people. Two pump stations, Vila Bela and Jardim da Conquista, pump water from the Rio Claro aqueduct, each through an 800 millimeter pipe. The Vila Bela pump station supplied the Jardim da Conquista tank with an average flow of 708 liters per second, and the Jardim da Conquista pump station supplied the Jardim São Pedro tank with an average flow of 388 liters per second. This Jardim da Conquista pump station suffered electrical shutdowns due to failures in the supply of the power utility. Each time this occurred, staff had to be onsite to restart the pumps and electrical panels of the pump station. • Using WaterCAD, Sabesp engineers were able to identify a viable solution. ROI • Using WaterCAD for pump redesign, Sabesp was able to reduce the time needed for the Jardim São Pedro storage tank to reach its increased volume from over 7 days to 16 hours. • The optimal solution identified using WaterCAD, will save BRL 1,100,000 yearly in energy costs. The tank and pump configuration of the problematic area. When this occurred at night, it was unsafe to send Sabesp personnel to the pump station because of the pump station’s proximity to dangerous areas. With the inability to restart the pump station at night, approximately 240,000 people would remain without water supply until the next day. Using WaterCAD, Sabesp was able to develop an optimal solution that not only provided continuous water supply to the inhabitants, but also saved BRL 700,000 in energy costs. Finding the Optimal Solution Sabesp initially considered disabling the Jardim da Conquista pump station, and transferring all pumping to the Vila Bela pump station, which would directly supply the Jardim São Pedro tank and as a result, supply the Jardim da Conquista tank. However, to better understand the operation of the entire system, Sabesp first performed hydraulic modeling of the system using WaterCAD. This enabled them to develop an alternative supply strategy. They determined that by constructing a 17,696-cubic-meter oversized water tank at Jardim São Pedro, if the pumps shutdown in the evening the tank would have sufficient autonomy to ensure water supply until the next morning. WaterCAD helped determine the operating conditions of the existing pumps and if they were working within operating range. Sabesp hydraulic modelers were then able to test the setup of new pumps that would best comply with a flow rate of 390 liters per second in regular operating conditions, as well as a flow rate of 800 liters per second in the case of nighttime pump shutdown, so that the water tank could supply the population for up to 12 hours. With WaterCAD, engineers were also able to find out how long the pumps would need to fill up the new tank before nightfall, in preparation for possible evening power outages. With this hydraulic modeling work, Sabesp reduced the time it would have taken for the Jardim São Pedro tank to reach its increased volume of 17,696 cubic meters, from 7 days and 3 hours to an average of 16 hours, increasing the water supply system reliability. In order to achieve this, the other tank, Jardim da Conquista, was also replaced, with doubled capacity from 4347 cubic meters to 8694 cubic meters, increasing operational security. With the new pump station configuration, WaterCAD solved a recirculation problem with the existing pumps, allowing a better use of Jardim da Conquista tank upstream of the Jardim da Conquista pump station, with a reduced minimum operating level by 4 meters.

Financial and Community Improvements “Using WaterCAD, Using WaterCAD, Sabesp was able to select the optimal pumps for the Jardim da Conquista pump station, thereby increasing water supply reliability, providing about 240,000 inhabitants with continuous water supply, and improving their quality of life. we were able to analyze and compare different solutions to Shutting off the Jardim da Conquista pumps during peak hours also reduced the electricity costs. Sabesp’s initial solution of closing the Jardim da Conquista pump station and transferring all pumping to the Vila Bela pump station would...