Catalogs >
BENDER >
COMTRAXX® COM465IP

COMTRAXX® COM465IP
8Pages

Catalog excerpts

COMTRAXX® COM465IP Condition monitor with integrated gateway for the connection of Bender devices to Ethernet TCP/IP networks

Open the catalog to page 1

Condition monitor with an integrated gateway for the connection of Bender devices to Ethernet TCP/IP networks Product description The COMTRAXX® COM465IP series features a condition monitor and is integrated into the existing EDP structure like any Ethernet-capable device. All Bender devices can be connected via the integrated interfaces. In addition, third-party devices can also be integrated into the system. The measured values, parameters and all other data can be checked and parameterised via the web interface or the display. It is possible to indicate and visualise alarms. By means of...

Open the catalog to page 2

Function module A • Assignment of individual texts for devices, channels (measuring points) and alarms. • Device failure monitoring. • E-mail notification to different users in case of alarms or system errors. • Device documentation of any device in the system can be generated.* * It contains all parameters and measured values belonging to the device, as well as device information such as serial number and software version. • System documentation can be created. It documents all devices in the system at once. *) reating device documentation of BMS bus devices is only possible if the gateway...

Open the catalog to page 3

Operating controls and connections 1 - “ON” LED: Flashes during start-up. The LED lights permanently as soon as the device is ready for operation. 2 - LEDs show activities on the different interfaces 3 - Supply voltage: see nameplate and ordering information 4 - Modbus/RTU interface: Terminals AMB and BMB (plug X1) 5 - BMS bus (Bender measuring device interface): Terminals ABMS and BBMS (plug X1) 6 - Ethernet port (RJ45) for connection to the PC network as well as BCOM (plug X2) 7 - Modbus RTU terminating resistor switch 8 - BMS bus terminating resistor switch 9 - Micro USB interface...

Open the catalog to page 4

Technical data Insulation coordination acc. to IEC 60664-1/IEC 60664-3 Rated voltage AC 250 V Rated impulse voltage/overvoltage category 4 kV/III Pollution degree 3 Protective separation (reinforced insulation) between (A1/+, A2/-) - [(AMB, BMB), (ABMS, BBMS), (X2), (X3, X4)] Supply voltage Supply voltage Us Frequency range Us Power consumption see ordering information see ordering information see ordering information Indications LEDs: ON ETHERNET IP MODBUS RTU BMS Ethernet (terminal X2) operation indicator data traffic Ethernet data traffic Modbus data traffic BMS lights during network...

Open the catalog to page 5

Technical data Connection Connection type pluggable push-wire terminals Push-wire terminals Conductor sizes Stripping length rigid/flexible flexible with ferrule, with/without plastic sleeve Multiple conductor, flexible with TWIN ferrule with plastic sleeve Push-wire terminal X1 Conductor sizes Stripping length rigid/flexible flexible with ferrule without plastic sleeve flexible with ferrule with plastic sleeve Operating mode continuous operation Mounting front-oriented, cooling slots must be ventilated vertically Degree of protection, internal components (IEC 60529) IP30 Degree of...

Open the catalog to page 6

Application example Integrated functions E-Mail notiﬁcation Backups Documentations Parameter Data transfer … Additional hardware necessary Solution for BACnet Solution for OPC …

Open the catalog to page 7

BENDER Group COM465IP_D00217_10_D_XXEN / 02.2022 / © Bender GmbH & Co. KG, Germany – subject to change! The specified standards take into account the edition valid until 02.2022 unless otherwise indicated. Bender GmbH & Co. KG Londorfer Straße 65 • 35305 Grünberg • Germany Tel.: +49 6401 807-0 • info@bender.de • www

Open the catalog to page 8

COMTRAXX® COM465IP 8Pages

Catalog excerpts

All BENDER catalogs and technical brochures

COMTRAXX® COM465IP
8Pages