ISOMETER® isoRW685W-D-B Insulation monitoring device for IT AC voltage systems with galvanically connected rectifiers and converters and for IT DC voltage systems especially for railway applications

ISOMETER® isoRW685W-D-B Insulation monitoring device for IT AC voltage systems with galvanically connected rectifiers and converters and for IT DC voltage systems especially for railway applications The ISOMETER® monitors the insulation resistance of unearthed AC/DC main circuits (IT systems). For the iso685-x and iso685-x-B types, the operating range of the nominal voltage Un can be extended via coupling devices. DC components existing in AC/DC systems do not influence the operating characteristics. A separate supply voltage allows de-energised systems to be monitored too. The maximum permissible...

Function description The insulation monitoring device continuously monitors the entire insulation resistance of an IT system during operation and triggers an alarm when the value falls below a preset response value. For measurement, the device has to be connected between the IT system and the protective earth conductor (PE). A measuring current in the µA range is superimposed onto the system which is recorded and evaluated by a microprocessorcontrolled measuring circuit. The measuring time is dependent on the selected measurement profiles, the system leakage capacitance, the insulation resistance...

Connection to the power supply voltage Us Connector for the IT system to be monitored Connector for the IT system to be monitored Connector for the IT system to be monitored Connection to PE Multifunctional I/O interface Ethernet interface Switchable terminating resistor for termination of the RS-485 interface Connector for alarm relay 1 Connector for alarm relay 2 isoxx685(W)-x-P. only: optional expansion interface for Bender products

ConnectionConnection requirementsConnection to a supply voltage J Check proper connection! Prior to commissioning the installation, check that the device has been properly connected and check the device functions. Perform a functional test using an earth fault via a suitable resistance. Connection to the Ethernet interface ETH If a monitored AC system contains galvanically coupled DC circuits, the following applies: An insulation fault can only be detected with its correct value when the rectifier valves carry a minimum current of >10 mA. Use 60/75 °C copper lines only! For UL and CSA applications,...

Insulation coordination acc. to IEC 60664-1/-3 IT system being monitored Rated voltage Overvoltage category Nominal system voltage range Un Measuring circuit (IC1) Supply circuit (IC2) Output circuit 1 (IC3) Output circuit 2 (IC4) Control circuit (IC5) Nominal system voltage range Un for UL applications Rated impulse voltage Response values Response value ^-1 (ALARM 1) Response value (ALARM 2) Relative uncertainty (acc. to IEC 61557-8) Hysteresis Rated insulation voltage Pollution degree outside {Un < 690 V) 3 Pollution degree outside (690 V < Un < 1000 V) 2 Time response Response time fan profile-dependent,...

SERVICE yellow ISOnet number of devices 2.20 Maximum nominal system voltage ISOnet AC, 690 V ISOloop number of devices 2.10 Cable length X1 (unshielded cable) < 10 m Cable length X1 (shielded cable, shield connected to PE < 100 m on one side) recommended: J-Y(St)Y min. 2x0.8 Max output current for supply via X1+/X1GND per 1 A Max output current for supply via A1/A2 in total on X1 200 mA Max output current for supply via A1/A2 in total on X1 VmaxX1 = 10 mA + 7 mA / V x Us* * Us is the supply voltage of the ISOMETER®. Negative values for /LmaxX1 are not permissible. Interface / protocol Data rate...

Screw-type terminals Operating mode Mounting position Degree of protection, internal components Degree of protection, terminals DIN rail mounting acc. to Screw mounting Enclosure material Flammability class (UL 94) ANSI Code Dimensions (W × H × D) Weight * For best ventilation, align cooling slots vertically (0°). Nominal current Tightening torque Conductor sizes Stripping length Wire cross-section rigid/flexible flexible with ferrule with/without plastic sleeve Multiple conductor, rigid Multiple conductor, flexible Multiple conductor, flexible with ferrule without plastic sleeve Multiple conductor,...

Standards and certifications The ISOMETER® has been developed in compliance with the following standards:

Bender GmbH & Co. KG Londorfer Straße 65 35305 Grünberg Germany Tel.: +49 6401 807-0 [email protected] www.bender.de © Bender GmbH & Co. KG, Germany Subject to change! The specified standards take into account the edition valid until 08.2024 unless otherwise indicated.