Remote alarm indicator for medical locations and other areas

COMTRAXX® CP305 - Control Panel The current overview of Bender devices with radio approval can be found in the Country list of RF Approval. Kr BENDERRemote alarm indicator for medical locations and other areasIntended use The COMTRAXX® CP305 control panel is for visual and acoustic signalling of operating and alarm messages from the Bender systems MEDICS®, ATICS®, EDS and RCMS. In MEDICS® monitoring systems, the CP305 fulfils the requirements of the standard DIN VDE 0100-710 concerning test functions for IT system monitoring and messaging from changeover devices. Testing of the IT system monitoring...

COMTRAXX® CP305 - Control Panel Device features The CP305 display shows the messages from all RS-485 bus participants that have been allocated to it via alarm addresses. This means that a CP305 can be used not only as an individual display, but several CP305s can also be employed as parallel displays in different rooms. The alarm colours for the LEDs are configurable (e.g. red for an alarm, yellow for a warning, such as an insulation fault or the like). In addition to the LED, there is also an alarm pop-up (display) as well as an entry in the alarm overview (web user interface) when a message...

COMTRAXX® CP305 - Control Panel System description Certification The CP305 remote alarm indicators are components of the MEDICS® systems. MEDICS® is an intelligent system that guarantees safe power supply in medical locations. In the example, the ICU is monitored from the station base via BMS bus. Connection example BMS and Ethernet In the example, the ICU can be monitored from the station base. In addition, remote maintenance is possible via the building services or Bender. For safe operation of the Medics® system in accordance with IEC 60364-7-710 and IEC 61557-8, we recommend operating the...

COMTRAXX® CP305 - Control Panel Connection example for Modbus RTU and Ethernet In the example, remote maintenance via the building services or by Bender is possible.

COMTRAXX® CP305 - Control Panel Kr BENDER Connection diagram

COMTRAXX® CP305 - Control Panel Legend for the connection diagram ** Devices without BMS bus connection, but with test input (e.g ISOMETER®)

COMTRAXX® CP305 - Control Panel Kr BENDER Technical Data Overvoltage category II and pollution degree 2 is related to the relay contacts. Further insulation coordination takes place after functional separation. Supply via plug-in terminal (A1/+, A2/-) Rated voltage Operating range of the supply voltage Nominal frequency Typical power consumption Maximum cable length with supply via B95061210 (24 V DC power supply unit 1.75 A) Operating mode Baud rate Cable length Shielded cable, one end of shield Galvanic separation Terminating resistor Device address Number of supported devices Master/slave...

COMTRAXX® CP305 - Control Panel Environment/EMC Switching elements Number of changeover contacts Operating principle (changeover contacts) Function Minimum contact load Electrical endurance under rated operating conditions N/C operation / N/O operation Programmable 100 mA/DC 5 V (0.5 W) Rated operational voltage AC 24 V / AC 24 V / DC 24 V Rated operational current AC 2 A / AC 2 A / DC 2 A Buzzer alarm Can be acknowledged, adoption of characteristics of Buzzer interval Configurable Buzzer frequency Configurable Buzzer repetition Configurable Device connections Flexible with ferrules, with/without...

COMTRAXX® CP305 - Control Panel Surface mounting Surface mounting requires use of the appropriate surfacemounting enclosure (part. no. B95100153). Any clearance between the surface-mounting enclosure and the wall must be compensated using washers. Never tighten the screws with a cordless screwdriver; only do so by hand. If this is disregarded, the surface-mounted housing can become warped. Dimension diagram flush-mounting enclosure Cavity wall and panel mounting Cavity wall mounting Panel mounting

COMTRAXX® CP305 - Control Panel Ordering information Device variants

Bender GmbH & Co. KG Londorfer Straße 65 35305 Grünberg Germany Tel.: +49 6401 807-0 [email protected] www.bender.de © Bender GmbH & Co. KG, Germany Subject to change! The specified standards take into account the edition valid until 08.2025 unless otherwise indicated.