*mydirectindustry

CC613

Product catalog summary

Overview: The CC613 charge controller is designed for use in electric vehicle charging stations, wallboxes, or street light charging points. It complies with IEC 61851-1 for charging mode 3 and supports dynamic load management, OCPP 1.5 and 1.6, and ISO 15118 Powerline Communication for plug & charge.

Device Features: The controller can operate in master or slave configurations, supports 4G, 3G, and 2G networks, and includes three USB interfaces for configuration and updates. It integrates a residual direct current monitoring module and supports single or three-phase systems up to 80 A.

Functional Description: The system includes an RCD type A and a contactor, with options for a Modbus meter and RFID module. It features dynamic load management to prevent peak and unbalanced loads, and supports up to 250 charging points in a network.

Technical Data: The controller operates at a nominal voltage of DC 12 V, with a maximum current of 750 mA. It includes a patented 6 mA DC residual current trip and supports various data interfaces including USB, Ethernet, and Modbus.

Environmental and Mechanical Conditions: The device operates in temperatures from -30 to 70 °C and is classified under various IEC standards for climatic and mechanical conditions. It has an IP20 protection rating and is designed for continuous operation.

Ordering Information: Various models are available with different features such as 4G modem, external Modbus, and user interface options. Accessories like RFID modules and measuring current transformers are also available.

Catalog excerpts

Charge controller for use in electric vehicle charging stations, wallboxes or street light charging points

Open the catalog to page 1

CC613 charge controller Charge controller for use in electric vehicle charging stations, wallboxes or street light charging points Device features (depending on the variant) • Charge controller in accordance with IEC 61851-1 (charging mode 3) • Configurable master and slave operation Setting up charging stations with two charging points: - 1 charge controller as data gateway with 4G modem - 1 charge controller as slave without 4G modem • Dynamic load management to optimally distribute the available power among all charging points and signal the maximum power available in each case to the vehicle...

Open the catalog to page 2

The charging system consists of an RCD type A and a contactor. These are directly connected to a type 1 or type 2 socket-outlet, or to a permanently mounted cable with a type 1 or type 2 plug (see "Wiring diagram"). • The charging system can be equipped with a meter. A Modbus meter is required to digitally read the energy consumption. The Modbus RTU lines are attached directly to the device. • A 12 V power supply is needed for operation. • An RFID module can be used for easy user interaction. • Current low toward the vehicle is released by enabling the contactor via an integrated 230 V control...

Open the catalog to page 3

CC613 charge controller Z BENDER Charging system with type 2 socket-outlet Terminal assignment CAUTION! Switching contact contactor and weld check at terminal H are only suitable for mains voltage (230 V)! Not permitted for SELV/PELV voltages.

Open the catalog to page 4

Technical data Overvoltage category within terminal H II Overvoltage category, terminal H and all other terminals III Rated impulse voltage, terminal H and all other terminals 6 kV Rated impulse voltage within terminal H 2.5 kV Double insulation between terminal H and all other terminals OCV III Basic insulation within terminal H OCV II Operating altitude AMSL < 2000 m Supply voltage (terminal B (0CV, +12CV)) Operating range of the nominal voltage DC 11.4...12.6 V Max. nominal current without USB load 400 mA Max. nominal current with USB load 750 mA Weld check (terminal H (WB, WA)) Outputs (depending...

Open the catalog to page 5

Ordering information 2) The PCB-variant can be combined with the connection cables of different lengths. E& BENDER The Power in Electrical Safety0 Londorfer StraBe 65 • 35305 GrGnberg • Germany Tel.: +49 6401 807-0 • [email protected] • www.bender.de

Open the catalog to page 6

CC613

CC613

Catalog excerpts

All BENDER GmbH & Co KG catalogs and technical brochures