[IteEgjQ Iu&?n©&jD [RajCffliQe I I20A FORKLIFT I 220A FORKLIFT I 220A VERSLIFT

Engineered for m manoeuvrability Bell’s range of forklifts have been engineered in response to a need for a manoeuvrable, lifting machine for use on rough terrain work sites. The Bell rough terrain Forklift has been the machine of choice in many applications, notably in brick yards, chicken farms and timber yards. It’s low maintenance cost, low fuel burn and low capital cost, result in a lowest cost solution for these challenging applications. The Bell philosophy of Strong Reliable Machines is clearly stamped on these products. Our network of aftersales centres provide the Strong Reliable Support...

Specifications - 120A FORKLIFT Engine Deutz F3L912, 3 cylinder, in-line, air cooled with integrated blower fan DRIVE PUMPS Model Eaton 78363 Type Axial piston, closed loop, manual control swash plate Governed Power 28 kW Max Torque 160 Nm @ 1400 rpm Control Direct control, foot linkage Governed Full Power Engine Speed 1 800 rpm DRIVE MOTORS Model Eaton 74315 Type Axial piston, closed loop Aspiration Naturally aspirated Engine Mounting 3 point rigid mounting Sump Material Cast aluminium Oil Capacity 9l Blower Failure Warning Mechanical linkage induces injector pump shut-off TRANSMISSION CHARGE...

4 100 mm Overall raising Height 2.5 ton CAPACITY Lowest cost per ton solutions Low fuel consumption low maintenance Designed for rough terrain operations, where agility and a light foot print are requirements

Specifications - 220A FORKLIFT Tail Wheel Inflation Pressure 3.0 bar Engine Deutz F4L912, 4 cylinder, in-line, air cooled with integrated blower fan DRIVE PUMPS Model Eaton 78363 Type Axial piston, closed loop, manualcontrol swash plate Unladen Ground Pressure Rear 1.28 bar Control Direct control, foot linkage BRAKES Service Brake Type Closed Loop Hydrostatic Wheel retardation Governed Power 46 kW Max Torque 230 Nm @ 1500 rpm Governed Full Power Engine Speed 2 150 rpm Max. rated speed 2 500 rpm Aspiration Naturally aspirated Engine Mounting 3 point rubber mounting Sump Material Cast aluminium...

4 100 mm Overall Raising Height 3.5 ton CAPACITY Lowest cost per ton solutions Low fuel consumption low maintenance Designed for rough terrain operations Where agility and productivity are requirements 7

Specifications - 220A VERSALIFT Engine Deutz F4L912, 4 cylinder, in-line, air cooled with integrated blower fan DRIVE PUMPS Model Eaton 78363 Type Axial piston, closed loop, manualcontrol swash plate Governed Power 46 kW Max Torque 234 Nm @ 1500 rpm Governed Full Power Engine Speed 2 150 rpm Max. rated speed 2 500 rpm Aspiration Naturally aspirated Engine Mounting 3 point rubber mounting Sump Material Cast aluminium Oil Capacity 9l Blower Failure Warning Mechanical linkage induces injector pump shut-off Low Idle 800 rpm High Idle 2 250 rpm Fuel Filtration Two stage. Spin-on water separator primary,...

Overall width of machine: 2 600 (8'7") HEIGHT OF THE LOWER FACE OF THE FORK ABOVE THE GROUND LEVEL IN mm (*) NOTE: THE ABOVE SAFE WORKING LOADS ARE ALL WITH A 500mm LOAD CENTRE

Verslift Options Material Handling Boom Fork Frames Lift Platform Lifting Extension Dangle Grab 1,8 m Class 2 or 3; 2,6 m Class 2 or 3 Tymes: 1,2 m Class 2 or 1,5 m Class 3

All dimensions are shown in millimetres, unless otherwise stated between brackets. Under our policy of continuous improvement, we reserve the right to change technical data and design without prior notice. Photographs featured in this brochure may include optional equipment.