Professional, Creditable, Successful LN80480T070IA9098 7.0 inch, 800*480 pixels resolution, RGB interface, TN-TFT-LCD Disclaimer：The product design is subject to alternation and improvement without prior notice. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 1 General Feature Feature Display Spec. Mechanical Characteristics Electrical Characteristics Temperature Range Pixel Configuration Pixel Pitch Viewing Direction Outside Dimension Active Area From left to right 50PIN_0.5mm Color Depth Driver Condition Operating Temp. Storage Temp. Note：Requirements on Environmental Protection: RoHS DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful Back light anode Back light cathode For external VCOM DC input Digital Power DE/SYNC mode select Data enable signal Frame synchronizing signal Line synchronizing signal Source right or left sequence control Gate up or down scan control Analog Power Global reset signal pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability. Normally pull high. For external VCOM DC input Dithering setting. DITH=“H”6bit resolution; DITH=“L”8bit resolution(default setting) DWIN Technology

Professional, Creditable, Successful 4 Electrical Characteristics 4.1 Driving TFT LCD Panel Item Digital Power Voltage Power for Analog Circuit Common Voltage 4.2 LED Backlight Specification Item DWIN Technology

Professional, Creditable, Successful 5 Timing Characteristics 5.1 Data Input Format 5.1.1 Vertical Timing Vertical display area VSD Back Porch (Blanking) Horizontal display area DCLK frequency HSD Back Porch (Blanking) DWIN Technology

Professional, Creditable, Successful SYNC Mode DWIN Technology

Professional, Creditable, Successful 5.2 Input Clock and Data Timing Diagram Item VDD power on slew rate RSTB pulse width CLKIN cycle time CLKIN pulse duty Data set-up time Data hole time Output stable time 5.3 Parallel 24-bit RGB Mode Timing Item CLKIN frequency CLKIN cycle time Tcwh CLKIN pulse duty Tclk=Tcwh+Tcwl Tcwl DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 6 Optical Characteristics Item Viewing Angle Left Contrast Ratio Color Temperature Test conditions: IF= 200 mA, and the ambient temperature is 25℃. DWIN Technology

Professional, Creditable, Successful Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 minutes operation, the optical properties are measured at the center point of LCD. Note 2: Definition of viewing angle range and measurement system. The viewing angle is measured at the center point of the LCD by BM-7A. Note 3: Definition of color temperature. When the radiation of the light source is exactly the same in the visible region and the absolute blackbody, the temperature of the blackbody is called the color temperature of the light...

Professional, Creditable, Successful Note 4: Definition of response time. The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Time ON (TON) is the time between photo detector output intensity changed from 90% to 10%. And time off (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Note 5: Definition of color chromaticity (CIE1931). Color coordinates measured at center point of LCD. Note 6: Definition of luminance. Measure the luminance of white state at center point. DWIN Technology

Professional, Creditable, Successful 7 Environmental Reliability Test NO Test Item High Temperature Operation High Temperature Storage Storage at High Temperature and Humidity Start with cold temperature, End with high temperature, IEC60068-2-14:1984, GB 2423.22-2002 Thermal Shock (non-operation) DWIN Technology

Professional, Creditable, Successful 8 Packing Capacity & Dimension Dimension Dimension(mm) Packing Capacity Size Packing instruction： The LCD is placed in the grid, covered with a PE static bag and compactly assembled, the upper and the lower layers of the grid are protected by buffer spaces. DWIN Technology

Professional, Creditable, Successful 9 Appearance Inspection 9.1 General rules for inspection 9.1.1 Anti-static wearables (anti-static wristbands, gloves) must be worn during the inspection. 9.1.2 Do not use bare hands to touch the position of the device, golden fingers, and the surface of the screen to prevent the sweat from human hands from causing oxidation and affecting the appearance. 9.1.3 It is forbidden to stack products out of specification and handle them with care to avoid damage to components. 9.1.4 The repaired products need to be inspected to prevent rosin and tin slag from exceeding...

Professional, Creditable, Successful 9.3 Inspection standards Type Dead pixels Defect Category Judgement Standard Test Items No dead pixels From different angles, the brightness is required to be uniform. Under the 64-level grayscale or pure black interface, there should be no uneven display brightness within the viewing angle range of 45°through 6% ND FILTER. Y series (TV film) LCD screen does not have specific requirements, and the picture inspection does not affect the display as qualified. Slight defect Display state Light leakage Slight defect Slight defect Within the effective area Spotted:...

Professional, Creditable, Successful 1. Does not affect the appearance from the front; 2. Does not affect the relevant alignment; 3. X≤1mm, Y≤1mm, N≤2. Slight defect Glass side Foreign objects Dirty 1. The foreign body on the side is not controlled; 2. The paint pen marks on the side are not controlled; 3. Side oily note printing is not allowed. Slight defect Cracks Goldfinger crease Heavy deficit Slight creases are not controlled; The crease is whitish and has lines, which is not allowed. Heavy deficit No damage to the line, D≤0.2mm; Damage to the line is not allowed. Heavy deficit Slight scratches...