Professional, Creditable, Successful LN80480T070IA3098 7.0 inch, 800*480 pixels resolution, RGB interface, TN-TFT-LCD Disclaimer：The product design is subject to alternation and improvement without prior notice. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 1 General Feature Feature Display Spec. Mechanical Characteristics Pixel Configuration Pixel Pitch Viewing Direction Outside Dimension Active Area From left to right 50PIN_0.5mm Color Depth Driver Condition Operating Temp. Storage Temp. Interface Electrical Characteristics Temperature Range Note: Requirements on Environmental Protection: RoHS. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful Back light anode Back light cathode For external VCOM DC input Digital Power DE/SYNC mode select Data ENABLE signal Frame synchronizing signal Line synchronizing signal Source right or left sequence control. Gate up or down scan control Analog Power For external VCOM DC input Global reset signal pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability. Normally pull high. Dithering setting. DITH= “H” 6bit. resolution; DWIN Technology DITH= “L” 8bit resolution(default setting)

Professional, Creditable, Successful 4 Electrical Characteristics 4.1 Driving TFT LCD Panel Item Digital Voltage Gate Driver High Voltage Gate Driver Low Voltage Analog Voltage Input Signal Voltage Input Logic High Voltage Input Logic Low Voltage Output Logic High Voltage Output Logic Low Voltage Forward Voltage Forward Current Power Consumption 4.2 LED Backlight Specification Item Note: 21 LEDs (3 LEDs Serial, 7 ways Parallel) DWIN Technology

Professional, Creditable, Successful 5 Timing Characteristics 5.1 Horizontal Input Timing DWIN Technology

Professional, Creditable, Successful 5.2 Vertical Input Timing 5.3 Parallel 24-bit RGB Mode Timing DWIN Technology

Professional, Creditable, Successful 5.4 Function Description 5.4.1 Power On/Off Sequence DWIN Technology

Professional, Creditable, Successful 5.4.2 Enter and Exit Standby Mode Sequence DWIN Technology

Professional, Creditable, Successful 6 Optical Characteristics Item Viewing Angle Left Response Time Color Gamut Contrast Ratio Test conditions: IF= 160 mA, and the ambient temperature is 25℃. DWIN Technology

Professional, Creditable, Successful Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 minutes operation, the optical properties are measured at the center point of LCD. Note 2: Definition of viewing angle range and measurement system. The viewing angle is measured at the center point of the LCD by BM-7A. Note 3: Definition of color temperature. When the radiation of the light source is exactly the same in the visible region and the absolute blackbody, the temperature of the blackbody is called the color temperature of the light...

Professional, Creditable, Successful Note 4: Definition of response time. The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Time ON (TON) is the time between photo detector output intensity changed from 90% to 10%. And time off (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Note 5: Definition of color chromaticity (CIE1931). Color coordinates measured at center point of LCD. Note 6: Definition of luminance. Measure the luminance of white state at center point. DWIN Technology

Professional, Creditable, Successful 7 Environmental Reliability Test NO Test Item High Temperature Operation High Temperature Storage Storage at High Temperature and Humidity Start with cold temperature, End with high temperature, IEC60068-2-14:1984, GB 2423.22-2002 Thermal Shock (non-operation) DWIN Technology

Professional, Creditable, Successful 8 Packing Capacity & Dimension Dimension Dimension(mm) Packing Capacity Size Packing instruction： The LCD is placed in the grid, covered with a PE static bag and compactly assembled, the upper and the lower layers of the grid are protected by buffer spaces. DWIN Technology

Professional, Creditable, Successful 9 Appearance Inspection 9.1 General rules for inspection 9.1.1 Anti-static wearables (anti-static wristbands, gloves) must be worn during the inspection. 9.1.2 Do not use bare hands to touch the position of the device, golden fingers, and the surface of the screen to prevent the sweat from human hands from causing oxidation and affecting the appearance. 9.1.3 It is forbidden to stack products out of specification and handle them with care to avoid damage to components. 9.1.4 The repaired products need to be inspected to prevent rosin and tin slag from exceeding...

Professional, Creditable, Successful 9.3 Inspection standards Type Dead pixels Defect Category Judgement Standard Test Items No dead pixels From different angles, the brightness is required to be uniform. Under the 64-level grayscale or pure black interface, there should be no uneven display brightness within the viewing angle range of 45°through 6% ND FILTER. Y series (TV film) LCD screen does not have specific requirements, and the picture inspection does not affect the display as qualified. Slight defect Display state Light leakage Linear foreign bodies Screen surface Within the effective...

Professional, Creditable, Successful Foreign objects Scratch Air bubbles Outside the effective area Foreign objects Scratches Air bubbles 。 Foreign objects are not checked, and bubbles are not allowed to D>1mm; Non-inductive scratches of no more than 0.1×8mm are allowed. Slight defect Slight defect 1. Does not affect the appearance from the front; 2. Does not affect the relevant alignment; 3. X≤1mm, Y≤1mm, N≤2. Slight defect Glass side Foreign objects Dirty 。 1. The foreign body on the side is not controlled; 2. The paint pen marks on the side are not controlled; 3. Side oily note printing is...