Professional, Creditable, Successful LI80480C050HA9098 5.0 inch, 800*480 pixels resolution, RGB interface, IPS-TFT-LCD Disclaimer：The product design is subject to alternation and improvement without prior notice. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 1 General Feature Feature Display Spec. Mechanical Characteristics Pixel Configuration Pixel Pitch Viewing Direction Outside Dimension Active Area From left to right 40PIN_0.5mm Color Depth Driver Condition Operating Temp. Storage Temp. Interface Electrical Characteristics Temperature Range Note: Requirements on Environmental Protection: RoHS. You can use dynamic screen saver wallpapers to avoid afterimages caused by fixed paper display for a long time. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful Power for LED backlight cathode Power for LED backlight anode Power ground Power Voltage for digital circuit 3.3V Green data(LSB) Green data Green data Green data Green data Green data Green data Green data(MSB) Blue data(LSB) Blue data Blue data Blue data Blue data Blue data Blue data Blue data(MSB) Power ground Pixel clock Standby mode, normally pull high STBYB= “1” normal operation; STBYB= “0”, timing control, source driver will turn off, all output are high-Z Horizontal sync input in parallel RGB. Negative polarity Vertical sync input in parallel RGB....

Professional, Creditable, Successful 4 Electrical Characteristics 4.1 Driving TFT LCD Panel Item Digital Power Voltage Common Voltage Forward Voltage Forward Current 4.2 LED Backlight Specification Item Note: 20 LEDs (4 LEDs Serial,5 ways Parallel) DWIN Technology

Professional, Creditable, Successful 5 Timing Characteristics 5.1 HV Mode Value Parameter Horizontal Display Area DLCK Frequency Vertical Display Area 5.2 Up-down Time Sequence 5.2.1 On DWIN Technology

Professional, Creditable, Successful 5.3 Mode DC Electrical Characteristics Spike/glitch rejection-DSI DWIN Technology

Professional, Creditable, Successful DSI clock channel timing Rising and fall time on clock and data channel DWIN Technology

Professional, Creditable, Successful 6 Optical Characteristics Item Viewing Angle Left Contrast Ratio Response Time Color Gamut Test conditions: IF= 100 mA, and the ambient temperature is 25℃. DWIN Technology

Professional, Creditable, Successful Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 minutes operation, the optical properties are measured at the center point of LCD. Note 2: Definition of viewing angle range and measurement system. The viewing angle is measured at the center point of the LCD by BM-7A. Note 3: Definition of color temperature. When the radiation of the light source is exactly the same in the visible region and the absolute blackbody, the temperature of the blackbody is called the color temperature of the light...

Professional, Creditable, Successful Note 4: Definition of response time. The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Time ON (TON) is the time between photo detector output intensity changed from 90% to 10%. And time off (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Note 5: Definition of color chromaticity (CIE1931). Color coordinates measured at center point of LCD. Note 6: Definition of luminance. Measure the luminance of white state at center point. DWIN Technology

Professional, Creditable, Successful 7 Environmental Reliability Test NO Test Item High Temperature Operation High Temperature Storage Vibration Test Package Drop Test 800mm, concrete floor,1corner, 3edges, 6 sides each time Shock Test 150pF,330Ω,Contact:±4KV,Air:±8KV Measure point: LCD glass and metal bezel DWIN Technology

Professional, Creditable, Successful 8 Packing Capacity & Dimension Dimension Dimension(mm) Packing Capacity Size Packing instruction： The LCD is placed in the grid, covered with a PE static bag and compactly assembled, the upper and the lower layers of the grid are protected by buffer spaces. DWIN Technology

Professional, Creditable, Successful 9 Appearance Inspection 9.1 General rules for inspection 9.1.1 Anti-static wearables (anti-static wristbands, gloves) must be worn during the inspection. 9.1.2 Do not use bare hands to touch the position of the device, golden fingers, and the surface of the screen to prevent the sweat from human hands from causing oxidation and affecting the appearance. 9.1.3 It is forbidden to stack products out of specification and handle them with care to avoid damage to components. 9.1.4 The repaired products need to be inspected to prevent rosin and tin slag from exceeding...

Professional, Creditable, Successful 9.3 Inspection standards Type Dead pixels Defect Category Judgement Standard Test Items No dead pixels From different angles, the brightness is required to be uniform. Under the 64-level grayscale or pure black interface, there should be no uneven display brightness within the viewing angle range of 45°through 6% ND FILTER. Y series (TV film) LCD screen does not have specific requirements, and the picture inspection does not affect the display as qualified. Slight defect Display state Light leakage Linear foreign bodies Screen surface Within the effective...

Professional, Creditable, Successful Foreign objects Scratch Air bubbles Outside the effective area Foreign objects Scratches Air bubbles 。 Foreign objects are not checked, and bubbles are not allowed to D>1mm; Non-inductive scratches of no more than 0.1×8mm are allowed. Slight defect Slight defect 1. Does not affect the appearance from the front; 2. Does not affect the relevant alignment; 3. X≤1mm, Y≤1mm, N≤2. Slight defect Glass side Foreign objects Dirty 。 1. The foreign body on the side is not controlled; 2. The paint pen marks on the side are not controlled; 3. Side oily note printing is...