Professional, Creditable, Successful LI24240C013HA2098 1.28 inch, 240*240 pixels resolution, RGB interface, IPS-TFT-LCD Disclaimer：The product design is subject to alternation and improvement without prior notice. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 1 General Feature Feature Display Spec. Mechanical Characteristics Pixel Configuration Pixel Pitch Viewing Direction Outside Dimension Active Area From left to right 40PIN_0.5mm Color Depth Driver Condition Operating Temp. Storage Temp. Interface Electrical Characteristics Temperature Range Note: Requirements on Environmental Protection: RoHS. You can use dynamic screen saver wallpapers to avoid afterimages caused by fixed paper display for a long time. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful Back light anode Back light cathode Back light cathode Power supply Serial data input/output bidirectional pin for SPI interface Serial clock input for SPI interface A Chip Select signal Clock signal Data enable Vertical sync input in RGB mode(short to GND if not used) Horizontal sync input in RGB mode(short to GND if not used) Blue Data Green Data DWIN Technology

Professional, Creditable, Successful 4 Electrical Characteristics 4.1 Driving TFT LCD Panel Item Digital Supply Voltage Forward Voltage Forward Current Reverse Current 4.2 LED Backlight Specification Item DWIN Technology

Professional, Creditable, Successful 5 Timing Characteristics 5.1 3-line Serial Interface Characteristics DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 5.4 Power Function Description Power Sequence DWIN Technology

Professional, Creditable, Successful 6 Optical Characteristics Item Viewing Angle Left Contrast Ratio Response Time Test conditions: IF= 40 mA, and the ambient temperature is 25℃. DWIN Technology

Professional, Creditable, Successful Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 minutes operation, the optical properties are measured at the center point of LCD. Note 2: Definition of viewing angle range and measurement system. The viewing angle is measured at the center point of the LCD by BM-7A. Note 3: Definition of color temperature. When the radiation of the light source is exactly the same in the visible region and the absolute blackbody, the temperature of the blackbody is called the color temperature of the light...

Professional, Creditable, Successful Note 4: Definition of response time. The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Time ON (TON) is the time between photo detector output intensity changed from 90% to 10%. And time off (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Note 5: Definition of color chromaticity (CIE1931). Color coordinates measured at center point of LCD. Note 6: Definition of luminance. Measure the luminance of white state at center point. DWIN Technology

Professional, Creditable, Successful 7 Environmental Reliability Test NO Test Item High Temperature Operation High Temperature Storage Storage at High Temperature and Humidity Start with cold temperature, End with high temperature, IEC60068-2-14:1984, GB 2423.22-2002 Thermal Shock (non-operation) DWIN Technology

Professional, Creditable, Successful 8 Packing Capacity & Dimension Dimension Dimension(mm) Packing Capacity Size Packing instruction： The LCD is placed in the grid, covered with a PE static bag and compactly assembled, the upper and the lower layers of the grid are protected by buffer spaces. DWIN Technology

Professional, Creditable, Successful 9 Appearance Inspection 9.1 General rules for inspection 9.1.1 Anti-static wearables (anti-static wristbands, gloves) must be worn during the inspection. 9.1.2 Do not use bare hands to touch the position of the device, golden fingers, and the surface of the screen to prevent the sweat from human hands from causing oxidation and affecting the appearance. 9.1.3 It is forbidden to stack products out of specification and handle them with care to avoid damage to components. 9.1.4 The repaired products need to be inspected to prevent rosin and tin slag from exceeding...

Professional, Creditable, Successful 9.3 Inspection standards Type Dead pixels Defect Category Judgement Standard Test Items No dead pixels From different angles, the brightness is required to be uniform. Under the 64-level grayscale or pure black interface, there should be no uneven display brightness within the viewing angle range of 45°through 6% ND FILTER. Y series (TV film) LCD screen does not have specific requirements, and the picture inspection does not affect the display as qualified. Slight defect Display state Light leakage Linear foreign bodies Screen surface Within the effective...

Professional, Creditable, Successful Foreign objects Scratch Air bubbles Outside the effective area Foreign objects Scratches Air bubbles 。 Foreign objects are not checked, and bubbles are not allowed to D>1mm; Non-inductive scratches of no more than 0.1×8mm are allowed. Slight defect Slight defect 1. Does not affect the appearance from the front; 2. Does not affect the relevant alignment; 3. X≤1mm, Y≤1mm, N≤2. Slight defect Glass side Foreign objects Dirty 。 1. The foreign body on the side is not controlled; 2. The paint pen marks on the side are not controlled; 3. Side oily note printing is...

Professional, Creditable, Successful 10 Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer...