Professional, Creditable, Successful LI12720T050TA3098 5.0 inch, 720*1280 pixels resolution, MIPI interface, IPS-TFT-LCD Disclaimer：The product design is subject to alternation and improvement without prior notice. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 1 General Feature Feature Display Spec. Mechanical Characteristics Pixel Configuration Pixel Pitch Viewing Direction Outside Dimension Active Area Number of Simultaneous Touches Minimum Touch Area Incell(Without Cover Lens) From left to right 40PIN_0.5mm Color Depth Driver Condition Operating Temp. Storage Temp. Electrical Characteristics Temperature Range Note: Requirements on Environmental Protection: RoHS. You can use dynamic screen saver wallpapers to avoid afterimages caused by fixed paper display for a long time. DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful Power Ground Power Ground Power Ground MIPI DSI CLOCK Positive MIPI DSI CLOCK Negative Power Ground Power Ground Power Ground Power supply to interface pins(1.8V) Positive input analog power for driver IC use(6.0V) Negative input analog power for driver IC use(-6.0V) Power supply to level shift IC(3.3V). If not used, please let it open Power Ground Tearing effect output signal. If not used, please let this pin open. LCM Reset pin, the LCD driver is initialized when RESET active low Power Ground Reset pin, the TP is initialized when RESET active low Power Ground...

Professional, Creditable, Successful 4 Electrical Characteristics 4.1 Driving TFT LCD Panel Item Logic Operating Voltage Input Signal Voltage Low Level Input Signal Voltage High Level Output Signal Voltage Low Level Output Signal Voltage High Level Backlight Power Consumption Operating Voltage 4.2 LED Backlight Specification Item Note: 12 LEDs (3 LEDs Serial,4 ways Parallel) DWIN Technology

Professional, Creditable, Successful 5 Timing Characteristics 5.1 Power on/off Sequence Power on/off Sequence Symbol TRise TFall TB-A TReset TReset-CMD Characteristics External Power Rise Time External Power Fall Time Delay Time between Two External Power Delay Time between External Power and Reset Reset to First Command in Display Sleep in Mode Timing Relation of Power on/off Sequence DWIN Technology

Professional, Creditable, Successful 5.2 DSI Timing Characteristics 5.2.1 High Speed Mode-Clock Channel Timing DSI Clock Channel Timing DSI Clock Channel Timing 5.2.2 High Speed Mode-Data Clock Channel Timing DSI Data to Clock Channel Timings DWIN Technology

Professional, Creditable, Successful DSI Data to Clock Channel Timings 5.2.3 High Speed Mode-Rise and Fall Timings Rise and Fall Timings on Clock and Data Channels Rise and Fall Timings on Clock and Data Channels Note: The display module has to meet timing requirements, what are defined for the transmitter(MCU)on MIPI D-Phy Standard. DWIN Technology

Professional, Creditable, Successful 5.2.4 Low Speed Mode-Bus Turn Around BTA from the MCU to the Display Module BTA from the Display Module to MCU Low Power State Period Timings-A Low Power State Period Timings-B DWIN Technology

Professional, Creditable, Successful 5.2.5 Data Lanes from Low Power Mode to High Speed Mode Data Lanes-Low Power Mode to High Speed Mode Timings Data Lanes-Low Power Mode to High Speed Mode Timings 5.2.6 Data Lanes from High Speed Mode to Low Power Mode Data Lanes-High Speed Mode to Low Power Mode Timings DWIN Technology

Professional, Creditable, Successful Data Lanes-High Speed Mode to Low Power Mode Timings 5.2.7 DSI Clock Burst-High Speed Mode to/from Low Power Mode Clock Lanes-High Speed Mode to/from Low Power Mode Timings Clock Lanes-High Speed Mode to/from Low Power Mode Timings DWIN Technology

Professional, Creditable, Successful 5.2.8 Timing for DSI Video Mode DWIN Technology

Professional, Creditable, Successful Limited Clock Channel Speed 5.2.9 Reset Timings DWIN Technology

Professional, Creditable, Successful DWIN Technology

Professional, Creditable, Successful 6 Optical Characteristics Item Viewing Angle Contrast Ratio Color Gamut Test conditions: IF= 80mA, and the ambient temperature is 25℃. DWIN Technology

Professional, Creditable, Successful Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 minutes operation, the optical properties are measured at the center point of LCD. Note 2: Definition of viewing angle range and measurement system. The viewing angle is measured at the center point of the LCD by BM-7A. Note 3: Definition of color temperature. When the radiation of the light source is exactly the same in the visible region and the absolute blackbody, the temperature of the blackbody is called the color temperature of the light...

Professional, Creditable, Successful Note 4: Definition of response time. The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Time ON (TON) is the time between photo detector output intensity changed from 90% to 10%. And time off (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Note 5: Definition of color chromaticity (CIE1931). Color coordinates measured at center point of LCD. Note 6: Definition of luminance. Measure the luminance of white state at center point. DWIN Technology

Professional, Creditable, Successful 7 Environmental Reliability Test NO Test Item High Temperature Operation High Temperature Storage Storage at High Temperature and Humidity Start with cold temperature, End with high temperature, IEC60068-2-14:1984, GB 2423.22-2002 Half Sine Wave 60G ,6ms,±X,±Y,±Z 3times for each direction Thermal Shock (non-operation) Vibration Test Package Drop Test DWIN Technology

Professional, Creditable, Successful 8 Packing Capacity & Dimension Dimension Dimension(mm) Packing Capacity Size Packing instruction： The LCD is placed in the grid, covered with a PE static bag and compactly assembled, the upper and the lower layers of the grid are protected by buffer spaces. DWIN Technology