PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE BJ AND MUST BE RETURNED TO BOE HF UPON ITS REQUEST SPEC. NUMBER PRODUCT GROUP **EV121X0M-N10- Product Specification Rev.PO Buyer ITEM SIGNATURE DATE Approved Reviewed Prepared

1.0 GENERAL DESCRIPTION 1.1 Introduction EV121X0M-N10 is a color active matrix TFT LCD using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 12.1 inch diagonally measured active area with XGA resolutions (1024 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.7M colors. 1.2 Features • Cell Thickness : 1.0t • RoHS Compliant • Display Mode: ADS • Interface: LVDS, 1 port 4 pair • Real 8 bit

PRODUCT GROUP SPEC. NUMBER Note: 1. Liquid Crystal driving voltage Due to the characteristics of LC Material, this voltage varies with environmental temperature. 2. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 °C max. and no condensation of water.

3.0 ELECTRICAL SPECIFICATIONS 3.1 Electrical Specifications <Table 3. Electrical specifications > TFT Gate ON Voltag TFT Gate OFF Voltage TFT Common Electrode Voltage TFT Kick-Back Voltage Max TFT Kick-Back Voltage Min LCD Panel Signal Processing Board LCD Panel Signal Current Backlight Input Voltage Backlight Input Current LCD Panel Display Power Backlight Power Note: 1. VGH is TFT Gate operating voltage. 2. VGL is TFT Gate operating voltage. The low voltage level of VGL signal must be fluctuates with same phase as Vcom. 3. Vcom must be adjusted to optimize display quality, as Crosstalk and...

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER Tcon Reset Interface Signal (LVDS) Valid video < Table 4. Sequence Table > Parameter

3.3 LVDS Interface Characteristic 3.3.1 Data Format !◄- LVCLKP LVCLKN < LVDS input data ideal strobe position > 3.3.2 LVDS input data mapping X ' LVCLKP LVCLKN Next circ|e < 8 bit LVDS input data mapping >

PRODUCT GROUP SPEC. NUMBER

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER Mini-LVDS driver VOD 0V MLCLKP-MLCLKN < Mini-LVDS VOD and VOS definition>

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER 3.3.4 AC Specification LVCLKP LVCLKN LV0P/N ~ LV3P/N TBIT=1/(F*7)(1) LVCLKP LVCLKN Note: (1) TBIT: Data period (2) Internal CLK sampling data window < LVDS channel to channel skew> FLVMOD FLVDEV FLVDEV < LVDS input SSC>

l.Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o' clock direction and the vertical or 6, 12 o' clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1). 2.Contrast measurements shall be made at viewing angle of 0= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state . (see FIGUR 1) Luminance Contrast Ratio (CR) is defined mathematically. Luminance when displaying...

5.Transmittance is the Value without APF and without CG. 6.The color chromaticity coordinates specified in the above table shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 7.The electro-optical response time measurements shall be made as FIGURE 3 The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Tf. 8. The lifetime is determined as the time at which luminance of LED become 50% of the initial brightness or not normal lighting at IPIN = 54mA on condition...

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER Figure2 White Luminance and Uniformity Measurement Locations (9 points) 1/10 Figure3 Response Time Testing Display data TR Optical Response

PRODUCT GROUP SPEC. NUMBER

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER 6.2 LC Align Direction & Pol absorption axis Figure3 The TFT and CF LC Align Direction Pol absorption axis Shown in Figure3, CF pol absorption axis is parallel with CF align direction(0°）, TFT pol absorption axis is vertical with TFT align direction（90°）

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER Pitch 0.2mm Width 0.1mm Space 0.1mm

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER 6.7 Cell Test Pad(unit : mm) ET Test Pad： A（左侧）VCOM DS DB DG DR B（右上侧）VCOM GS GE GO

PRODUCT GROUP SPEC. NUMBER NOTE 1.MATERIAL: PET 2. [*] : CRITICAL PARAMETERS. CPK CONTROL POINT IO] : THICKNESS CONTROL POINT 3.THICKNESS : BEFORE MOLDING 1.1mm 4. Weight: 122g±10% 5.SURFACE RESISTANCE: 1 k1Q^4SR< 1 *10*9 ohm/sq, 6.ANTISTATIC HOLDING TIME : PERMANENT /.KEEPING CLEAR & NO SCRATCH, BURR AND SALIENT POINT AT THE ALL SURFACE 9.TOLERENCE OF CRITICAL PARAMETER IS ±Q,3mm OTHERS REFER TO DRAWING 10.DRAFT ANGLE : 4° 11 .Halogen Free & RoHS & REACH

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER 7.0 PACKING INFORMATION 7.3 Inner Box Label Format DATE： XXXX.XX.XX RoHS Compliant Serial number marked part needs to print, show as follows: 1. FG-CODE(Before 12 bit) --- EV121X0M-N10 2. Product quantity---3 3. Box ID 4. Date 5. FG-Code After four +Product Grade + Revision Code---1850PW Total Size:110×56mm Box Label Naming Rule ： Code Code Description Product Model

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER 7.0 PACKING INFORMATION 7.4 Outer Box Label Format DATE： XXXX.XX.XX RoHS Compliant Serial number marked part needs to print, show as follows: 1. FG-CODE(Before 12 bit) --- EV121X0M-N10 2. Product quantity---18 3. Box ID 4. Date 5. FG-Code After four +Product Grade + Revision Code---1850PW Total Size:110×56mm Box Label Naming Rule ： Code Code Description Product Model

PRODUCT GROUP TFT- LCD PRODUCT SPEC. NUMBER 7.0 PACKING INFORMATION 7.5 Pallet Label Format MODEL : XXXXXXXX – XXX QTY : XXXX PACK DATE : XXXX/XX/XX ③ PALLET Serial number marked part needs to print, show as follows: 1. FG-CODE(Before 12 bit) --- EV121X0M-N10 2. Product quantity---288 3. Packing Date 4. Pallet ID 5. FG-Code After four +Product Grade + Revision Code---1850PW Total Size:100×80mm Pallet Label Naming Rule ： Digit Code MODEL TYPE