PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE HF AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HF AND MUST BE RETURNED TO BOE HF UPON ITS REQUEST PRODUCT GROUP ISSUE DATE SPEC. NUMBER BUYER SUPPLIER HEFEI BOE Optoelectronics Technology CO., LTD BUYER SIGNATURE DATE ITEM SUPPLIER SIGNATURE DATE Prepared Reviewed Approved

PRODUCT GROUP ISSUE DATE 2020-04-30 PAGE SPEC . TITLE B3 EV101WXM-N10 Product Specification REVISION HISTORY ( √ )preliminary specification ( )Final specification REV. Initial Release

1.1 Introduction EV101WXM-N10 is a color active matrix TFT LCD module using amorphous silicon TFT 's (Thin Film Transistors) as an active switching devices. This module has a 10.1 inch diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16.2M colors. 1.2 Features • 1 Port LVDS Interface Input; • 6+2bit color depth, display 16.2M colors • Thin and light weight • High luminance and contrast ratio, low reflection and wide viewing angle...

Note : 1) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 °C max. and no condensation of water.

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VBAT=3.8V, Frame rate fv=60Hz and Clock frequency = 156.8MHz. Test Pattern of power supply current a) Typ : Mosaic 8x6 Pattern(L0/L255) b) Max : L255

1. PLED = VDD xIVDD (Without LED converter transfer efficiency) 2. The life time of LED, 30,000Hrs, is determined as the time at which luminance of the LED is 50% compared to that of initial value at the typical LED current on condition of continuous operating at 25 ± 2°C. 3. Only under the above operating conditions could the life time of LED be guaranteed.

3.4 DC Specification< Table7. DC Specification > Parameter

PRODUCT GROUP SPEC. TITLE ISSUE DATE Mini-LVDS driver VOD 0V MLCLKP-MLCLKN < Mini-LVDS VOD and VOS definition>

PRODUCT GROUP ISSUE DATE SPEC. TITLE 3.5 AC Specification LVCLKP LVCLKN LV0P/N ~ LV3P/N TBIT=1/(F*7)(1) LVCLKP LVCLKN Note: (1) TBIT: Data period (2) Internal CLK sampling data window < LVDS channel to channel skew> FLVMOD FLVDEV FLVDEV < LVDS input SSC>

PRODUCT GROUP SPEC. TITLE Tcon Reset Interface Signal (LVDS) Valid video < Table 10. Sequence Table > Parameter

PRODUCT GROUP TFT- LCD PRODUCT SPEC. TITLE 3.8 Input Color Data Mapping < Table11. Input Signal and Display Color Table > Color & Gray Scale Basic Colors Gray Scale of Green Gray Scale of Blue Gray Scale of White Black Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White Input Data Signal Green Data Blue Data

Display Position of Input Data (V-H)

NotelrLuminance measurement The test condition is at ILED=100mA and measured on the surface of LCD module at 25°C. •The data are measured after LEDs are lighted on for more than 5 minutes and LCM displays are fully white. The brightness is the center of the LCD. Measurement equipment CS2000 or similar equipments (Field of view:ldeg,Distance:50cm) • Measuring surroundings: Dark room. • Measuring temperature: Ta=25°C. •Adjust operating voltage to get optimum contrast at the center of the display. • Measured value at the center point of LCD panel must be after more than 5 minutes while backlight...

Measurement equipment: DMS501 or similar equipments. Test method: we define 8 grays L0-L7,the grays of L0-L7 were defined as:0,36,73, 109, 146, 182, 219, 25 5. Theoutputsignalsofphotodetectoraremeasuredwhentheinputsignalsarechanged from "Lx" to "Ly" , x, y= [0, 7]. The response time is defined as the time interval between the 10% and 90% of amplitudes. The result of the test can be noted as below: DAS-RD-2019026-0

Note 6: Color Coordinates of CIE 1931 The test condition is at ILED=100mA and measured on the surface of LCD module at 25°C. Measurement equipment:CS2000 or similar equipments The Color Coordinate (CIE 1931) is the measurement of the center of the display shown in below figure. Note 7: Definition of Color of CIE Coordinate and NTSC Ratio. S= afeaofRGBlnang|exlOO% area of NTSC triangle Note 8: Polarization Direction Definition •Viewing direction is normal user viewing direction which is vertical to the display surface •The polarizer which is closer to viewer is defined as Front Polarizer •The...

PRODUCT GROUP ISSUE DATE SPEC. TITLE Note 9: Definition of gray inversion angle lRefer to the graph of note 9. lUsing luminance test method. lTest pattern : 128 gray lIf the viewing direction is 12 o’clock ,then test the luminance while θ=-60°,θ=-50°, θ=-40°, θ=-30°, θ=-20°, θ=-10°, θ=0°, θ=10°, θ=20°, θ=30°, θ=40°, θ=-50°, θ=60°. The luminance test as figure below:

6.0 PACKING IN FORMATION : LCM ) Packing procedure: -.Put 2pcs Panel on Tray put lepe spacer upon the panel -.Put 21pcs Tray in PE Bag The Top Tray is Empty 40pcs LCM/Box -. 3layers/ Pallet -. 4 boxes/ Layer -. 480pcs Panel / Pallet 6.1 Packing Note^fipJ^^ : LCM) • Box Dimension: 500mm(W) x 400mm(D) x 300mm(H) • Package Quantity in one Box: 40pcs

PRODUCT GROUP ISSUE DATE SPEC. TITLE Label Size :110mm*55mm Contents Model : LCM Q`ty : 40pcs/Box Serial No. : Box Serial No. as shown below. Date : Packing Date FG Code : FG Code of Product

Please pay attention to the followings when you use this TFT LCD Module. 8.1 Mounting Precautions • Use finger-stalls with soft gloves in order to keep display clean during the incoming inspection and assembly process. • You must mount a module using specified mounting holes (Details refer to the drawings). • You should consider the mounting structure so that uneven force (ex. Twisted stress, Concentrated stresses not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. • Do not apply...