Wireless inclinometer sensor | tilt / inclination / slope monitoring | Low-cost version FEATURED VIDEO year Warranty USER GUIDE requires beanGateway® (wireless receiver) for operation. High precision bi-axis inclinometer with great measurement repeatability (±0.005° for bi-axis ±15° version, and ±0.006° for bi-axis • Time-synchronized wireless sensor networks (±2.5ms of accuracy) Embedded data logger : up to 1 million data points (with events dating) • High Gain Antenna : • Integrated Low-profile Antenna : 150m max* * , 30-60m (N.L.O.S.) *High Gain Antenna Pointing to Vertical position, BeanGateway® Installed on a mast 10 meters height with 9dBi Antenna **Low Profile Antenna Pointing to Vertical position, BeanGateway® Installed on a mast 10 meters height with 9dBi Antenna

Structural Health Monitoring Condition Monitoring Land Surveying For further information about bridge monitoring, please read the following applications note : AN_RF_002 – “Bridge monitoring with BeanAir® products” Time-Synchronized Wireless IIOT SensorS TimeSync function brings time-synchronization over the Wireless IIOT Sensors (±2.5ms of accuracy between each wireless IOT sensors) and contributes to enhance user experience about correlation of remote sensing data and modal analysis. Clock Transmission Wireless IOT Sensors Supervision Software Wireless IOT Sensors coordinator Indoor Version

2.4GHz INC Remote Configuration & Monitoring BeanScape®2.4GHz Basic The BeanScape® 2.4GHz application allows the user to view all the data transmitted by the BeanDevice® 2.4GHz INC Thanks to the OTAC (Over-the-Air configuration) feature, the user can remotely configure the BeanDevice® 2.4GHz INC SEVERAL DATA ACQUISITION MODES ARE AVAILABLE ON THE BEANDEVICE® INC : • Low Duty Cycle Data Acquisition mode (LDCDA) : the data acquisition is immediately transmitted by radio. The transmission frequency can be configured from 1s to 24h. • Survey Mode: the measured value is transmitted by radio whenever...

2.4GHz INC Embedded data logger up to 1 million data points The BeanDevice® 2.4GHz INC integrates an embedded datalogger, which can be used to log data when a Wireless IIOT Sensors can not be easily deployed on your site. All the data acquisition are stored on the embedded flash and then transmitted to the BeanGateway® 2.4GHz when a Wireless IIOT Sensors is established. The data logger function is compatible with all the data acquisition mode available on the BeanDevice® 2.4GHz INC : - LowDutyCycle Data Acquisition - Survey - Streaming packet EXAMPLE : TILT MONITORING ON A BRIDGE • In standalone...

• Beangateway is positioned in Line Of Sight toward sensor (no obstacles, no radio interferences) with High Gain Antenna, with a Height of 3 meters minimum. 26dBm High Gain Directional Antenna is used om gateway side. • On sensor side : Radome Antenna should point to Vertical Direction for better Coverity

2.4GHz INC Getting started with a Wireless IIOT SensorS Wireless IOT Sensors coordinator Indoor Version OR Wireless IOT Sensors Supervision Software Wireless IOT Sensors coordinator Outdoor Version Rethinking Sensing Technology The BeanDevice® 2.4GHz INC operates only on our Wireless IIOT Sensors, you will need the BeanGateway® 2.4GHz and the BeanScape® 2.4GHz for starting a wireless IIOT sensors. For further information about BeanDevice® battery life : TN-RF-002 Current consumption in active & sleeping mode TN-RF-012 Beandevice autonomy in Streaming and Streaming Packet Mode Beandevice® 2.4GHZ...

2.4GHz INC External Power supply wiring code M8 Socket (A-Coding) - Pin Assignation Pin 4 Pwr+ (4VDC) Xtend version only Pin 3 Pwr+ (8-28VDC) Interface Name Power Supply 8-28VDC Power Supply 4VDC (available on Xtend version only) Ground Wire Color (A-coding) Blue Black Brown M8 Plug (A –Coding) - Pin Assignation Pin 1 Gnd Pin 4 Pwr+ (4VDC) Xtend version only Pin 3 Pwr+ (8-28VDC) Do not power PIN4 and PIN3 at the same time, you will damage your Beandevice External Power-Supply External Battery Pack High efficiency solar panel with solar charging controller and Lead-acid battery Ref: X-SOL-SLP-VOUT-CL...

2.4GHz INC drawing “ No screw mounting option, this device should be glue mounted or use a tape/cable-tie ” If you need screw mounting option , please choose version: HI-INC-XR-SCM Buchholzer Straße 65, 13156 Berlin, Germany Above given technical data are only for information purpose. ® Sensors has right to change product specifications without notice.