2.4GHz AN-V Wireless IOT Data Acquisition (DAQ) Instrument Voltage inputs (±5V or ±10V) | built-in datalogger Product Video user guide quick start step file mechanical drawing Main Features • Analog inputs ±5V or ±10V ( 4 channels ) • Embedded data logger up to 1 million data points • Integrated sensor power supply, software configurable 4.5V to 20V • Wireless transmission IEEE 802.15.4 with antenna diversity • Measurement repeatability less than ± 0.01% on the full scale • Integrated rechargeable Lithium-Ion battery

Structural Health Monitoring Condition monitoring Remote Monitoring

EMBEDDED DHTH LOGGER UP TO 1 MILLION DRTR POINTS The BeanDevice® 2.4GHz AN-V integrates an embedded data logger, which can be used to log data when a Wireless Network can not be easily deployed on your site. All the data acquisitions are stored on the embedded flash and then transmitted to the Wireless receiver (BeanGateway® 2.4GHz) whenever a Wireless Networks is established. The datalogger function is compatible with all the data acquisition mode available on your BeanDevice® 2.4GHz AN-V • Low Duty Cycle data acquisition with a measurement heartbeat from 1s to 24h • Alarm data acquisition with...

Remote configuration & monitoring The BeanScape® 2.4GHz software helps the user to view all the data measurements transmitted by the BeanDevice® 2.4GHz AN-V. Different data acquisition modes can be remotely configured from the software : • Low Duty Cycle Data Acquisition mode (LDCDA) : the data acquisition is immediately transmitted by radio. The transmission frequency can be configured from 1s to 24h. • Alarm Mode : the measured value is transmitted by radio whenever an alarm threshold (fixed by the user) is detected (3 alarms threshold levels are available Alert-Action-Alarm ). The device sends...

CONFIGURABLE SENSOR POWER SUPPLY The sensor is directly powered by a high accuracy and adjustable DC/DC converter integrated inside the device. The excitation voltage is remotely configurable through the BeanScape® 2.4GHz (4.5 to 20V). GETTING started WITH A WIRELESS IOT SENSORS The BeanDevice® 2.4GHz ANV operates only on our Wireless IIOT Sensor, you will need the BeanGateway® 2.4GHz and the BeanScape® 2.4GHz for starting a wireless IIOT sensors Indoor Version OR Wireless IIOT Sensors Supervision software Outdoor Version Product specifications are subject to change without notice. Contact Beanair...

MR-Measurement Range 5: ±5V measurement range , 10: ±10V measurement range Example: BND-2.4GHZ-ANV-4CH-5, BeanDevice® AN-V with four channels , measurement range: ±5V Signal Conditionning Analog voltage measurement Number of channels 4 Channels A/D Converter 16 bits - SAR Architecture (Successive Approximation Register) with temperature compensation Measurement range (analog polarity is dynamically BND-2.4GHZ-ANV-4CH -5: ±5V (bipolar) or 0-10 V (unipolar) configurable from the BeanScape® 2.4GHz) BND-2.4GHZ-ANV-4CH -10: ±10V (bipolar) or 0-20 V (unipolar) Repeatability (full scale, @ 25°C, Static...

^feanDevice8 2.4GHz AN-V High Gain antenna option • Beangateway is positioned in Line Of Sight toward sensor (no obstacles, no radio interferences) with High Gain Antenna, with a Height of 3 meters minimum. 26dBm High Gain Directional Antenna is used om gateway side. • On sensor side : Radome Antenna should point to Vertical Direction for better Coverity ON/Off push button Network Reset push button M8-3 Pins socket for external power supply Wireless Data Acquisition System M12-4 Pins female socket for sensor interafce Eyelet for wall mounting

2.4GHz AN-V Sensor Wiring Code M12 Socket Pin assignation M12 Socket Positioning Notch Sensor Chanel Label positioning notch Wiring Code (Sensor Side)-Sensor with Analog Unipolar Output NOTCH PIN 2: sens- CAPTION PIN 2 : Connected to Electrical Ground PIN 3 (Gnd) : Electrical Ground M12-4Pins Plug PIN1 ( Pwr+) : Sensor power supply PIN 4 (Sens +) : Sensor Signal + input Wiring Code (Sensor Side)-Sensor with Analog Bipolar Output NOTCH PIN2: sens- CAPTION PIN2 : Sensor signal - input PIN1 ( Pwr+) : Sensor power supply PIN3 (Gnd) : Electrical Ground PIN4 (Sens +) : Sensor Signal + input If you...

BfeanAir WIRELESS HOT SENSORS HCCESSDRIE^^ f^anDevice 2.4GHz AN-V AC/DC Power supply with M8 Plug - Wall plug-in power supply, - AC Power plug: Europe/UK Northamerica /China/Australia N-Type cable [Male/Male] . length: 1 meter / 2 meters / 5 meters . Cable type: RF-5/H155 Omnidirectiona antenna 5dBifor outdoor use Ref: HG_OMNI_5_OUT_DBI - Waterproof design - Professional N-type design reduces stress - N-type, Male, Reverse Polarity, - Wind survival: up to 180Mph Watertight IP65 Molded Cable with M8 plug Ref:CBL-M8-2M (cable length : 2 meters] CBL-M8-5M (cable length : 5 meters] CBL-M8-10M (cable...