2.4GHz AN-420 Wireless IOT Data Acquisition(DAQ) Instrument 4-20mA (current loop) inputs | built-in datalogger Product Video user guide quick start mechanical drawing Main Features • Embedded data logger up to 1 million data points • Wireless data logger with 4-20mA current loop inputs (4 channels) • Wireless transmission IEEE 802.15.4 with antenna diversity • Integrated rechargeable Lithium-Ion battery • Integrated sensor power supply, software configurable 4.5V to 20V • Measurement repeatability less than ± 0.01% on the full scale

Structural Health Monitoring Condition monitoring Remote Monitoring

iBeanAir WIRELESS HOT SENSORS EMBEDDED DHTH LOGGER UP TO 1 MILLION DRTR POINTS The BeanDevice® 2.4GHz AN-420 integrates an embedded data logger, which can be used to log data when a Wireless Network can not be easily deployed on your site. All the data acquisitions are stored on the embedded flash and then transmitted to the Wireless receiver (BeanGateway® 2.4GHz) whenever a Wireless Networks is established. The datalogger function is compatible with all the data acquisition mode available on your BeanDevice® 2.4GHz AN-420 • Low Duty Cycle data acquisition with a measurement heartbeat from 1s...

Remote configuration & monitoring The BeanScape® 2.4GHz software helps the user to view all the data measurements transmitted by the BeanDevice® 2.4GHz AN-420. Different data acquisition modes can be remotely configured from the software: • Low Duty Cycle Data Acquisition mode (LDCDA) : the data acquisition is immediately transmitted by radio. The transmission frequency can be configured from 1s to 24h. • Alarm Mode : the measured value is transmitted by radio whenever an alarm threshold (fixed by the user) is detected (3 alarms threshold levels are available Alert-Action-Alarm ). The device...

CONFIGURABLE SENSOR POWER SUPPLY The sensor is directly powered by a high accuracy and adjustable DC/DC converter integrated inside the device. The excitation voltage is remotely configurable through the BeanScape® 2.4GHz (4.5 to 20V). GETTING started WITH A WIRELESS IOT SENSORS The BeanDevice® 2.4GHz AN-420 operates only on our Wireless IIOT Sensors , you will need the BeanGateway® 2.4GHz and the BeanScape® 2.4GHz for starting a Wireless IIOT Sensors Indoor Version OR Wireless IOT Sensors Supervision software Outdoor Version Product specifications are subject to change without notice. Contact...

• Beangateway is positioned in Line Of Sight toward sensor (no obstacles, no radio interferences) with High Gain Antenna, with a Height of 3 meters minimum. 26dBm High Gain Directional Antenna is used om gateway side. • On sensor side : Radome Antenna should point to Vertical Direction for better Coverity

PRODUCT OVERVIEW ON/Off push button M8-3 Pins socket for external power supply Wireless Data Acquisition System cmTirm* Power Supply M12-4Pins female socket for sensor interface Eyelet for wall mounting \^anAir ProcessSensor WWW.BERNRIR.COM

Sensor Wiring Code M12 Socket Pin assignation M12 Socket Positioning Notch Sensor Chanel Label positioning notch M12 4pins Female Wiring code (BeanDevice® AN-420 side ) CAPTION PIN1 ( Pwr+) : Sensor power supply PIN 4 (SI) : Signal input PIN 2 : Not used PIN 3 (Gnd) : Electrical Ground

OeanAir WIRELESS HOT SENSORS M12-4pins Male Plug Wiring code [sensor side) PIN 2:Not used must be connected to Gnd PINT: Pwr+ PIN1 [ Pwr+]: Sensor power supply PIN2 : Not used must be connected to Gnd PIN4 [SI]: Signal input PIN3 [Gnd]: Electrical Ground Instructions for connecting a 2-wire sensor : - Connect the sensor wire "Loop Supply” to PIN1 (Pwr+) - Connect the sensor wire "Current output” 4-20mA to PIN4 (SI) - Use a jumper cable to connect PIN3(Gnd) to PIN2

BfeanAir WIRELESS HOT SENSORS HCCESSDRIE^ f^anDevice2.4GHz AN-420 AC/DC Power supply with M8 Plug N-Type cable [Male/Male] Ref:M8-PWR-12V - Wall plug-in power supply, Output: 12VDC, M8-3Pins plug - AC Power plug: Europe/UK Northamerica /China/Australia Molded Cable with M8 plug Ref:CBL-M8-2M (cable length : 2 meters] CBL-M8-5M (cable length : 5 meters] CBL-M8-10M (cable length : 10 meters] CDNTHCTU^^ Headquarter: Buchholzer Strafe 65, 13156 Berlin, Germany . length: 1 meter / 2 meters / 5 meters . Cable type: RF-5/H155 Email: Omnidirectiona antenna 5dBifor outdoor use Ref: HG_OMNI_5_OUT_DBI -...