Catalogs >
BD|SENSORS GmbH >
HYDROSTATIC PROBES SCREW-IN TRANSMITTER

HYDROSTATIC PROBES SCREW-IN TRANSMITTER
1 / 100Pages

Catalog excerpts

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 1

PRODUCT CATALOGUE HYDROSTATIC PROBES SCREW-IN TRANSMITTER pressure measurement

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 2

„Successful medium-sized because they are active in many companies are not successful areas, but rather because they better than anyone else“ This is our philosophy. That´s why BDSENSORS has concentrated on electronic pressure measurement technology from the beginning. With our unremitting product and and quality strategy we have been successful in becoming a major player on the world market for electronic pressure sensing devices within a few year

Open the catalog to page 2

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 3

pressure measurement With 260 employees at 4 locations in Germany, the Czech Republic, Russia and China BD|SENSORS has solutions from 0.1 mbar to 6000 bar: > pressure sensors, pressure transducers pressure transmitters > electronic pressure switches > pressure measuring devices with display and switching outputs > hydrostatic level probes PRECISION: STAINLESS STEEL PROBES stainless steel sensor 5-8 INDUSTRY: STAINLESS STEEL PROBES stainless steel sensor 21-36 Two pressure transmitters and a submersible probe, based on a stainless steel silicon sensor were the beginning. Today the...

Open the catalog to page 3

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 4

aggressive media pressure range / level [mH2O] ceramic sensor stainless steel sensor housing material stainless steel

Open the catalog to page 4

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 5

LMP 308i Nominal pressure from 0 ... 4 mH2O up to 0 ... 200 mH2O Output signals 2-wire: 4 ... 20 mA 3-wire: 0 ... 10 V others on request Special characteristics ► diameter 35 mm ► cable and sensor section separable ► excellent accuracy ► communication connection Separable Stainless Steel Probe Precision Stainless Steel Sensor accuracy according to IEC 60770: 0.1 % FSO The separable precision stainless steel probe LMP 308i is designed for continuous fill level and level measurement of water and liquid mediums. The signal processing of sensor signal is done by digital electronics with 16-bit...

Open the catalog to page 5

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 7

Technical Data Accessories Technical Data Precision Stainless Steel Probe Wiring diagram / connector 2-wire-system (current) supply + Pin configuration Electrical connection Supply + Supply – Signal + (for 3-wire) RxD TxD GND Shield cable colours (DIN 47100) wh (white) bn (brown) gn (green) gn/ye (green / yellow) separated version version with corrugated p

Open the catalog to page 7

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 8

Ordering code standard with communicaton interface 3 prepared for mounting 4 with stainless steel pipe cable protection with stainless steel corrugated pipe with pipe length in m customer consult consult consult 1 cable with integrated air tube for atmospheric pressure reference 2 available on request: calibration of individual pressure range higher than 400 mbar with accuracy 0.1 % 3 Software, interface and cable have to be order separately (Ordering code: CIS-Set 510; Software appropriate for Windows3 95, 98, 2000, NT Version 4.0 or newer and XP) 4 stainless steel pipe is not part of the...

Open the catalog to page 8

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 9

LMK 382H Stainless Steel Probe with HART®-communication Ceramic Sensor accuracy according to IEC 60770: 0.1 % FSO Nominal pressure from 0 ... 60 cmH2O up to 0 ... 200 mH2O Output signals The stainless steel probe LMK 382H has been designed for continous level measurement in waste water, waste and higher viscosity mediums. Basic element is a robust and high overpressure capable capacitive ceramic sensor e.g. for low levels. Sewage waste water treatment water recycling Fuel / Oil level monitoring in open tanks with low filling heights fuel storage tank farms biogas plants BDSENSORS...

Open the catalog to page 9

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 11

6 for optional stainless steel pipe following designation is valid: "II1G Ex ia IIC T4" (zone 0) HART® is a registered trade mark of HART Communication Foundation; Windows® is a registered trade mark of Microsoft Corporation

Open the catalog to page 11

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 12

Seals Electrical connection FKM EPDM FFKM customer PVC-cable PUR-cable FEP-cable TPE-cable Special version 1 cable with integrated air tube for atmospheric pressure reference 2 only possible for PN > 1 bar 3 stainless steel pipe is not part of the supply HART® is a registered trade mark of HART Communication Foundation This document contains product specifications; properties are not guaranteed. Detailed information about options are defined in the datasheet. Subject to change without notice.

Open the catalog to page 12

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 13

LMK 458H Probe with HART®-communication for Marine and Offshore Ceramic Sensor accuracy according to IEC 60770: 0.1 % FSO Nominal pressure from 0 ... 60 cmH2O up to 0 ... 200 mH2O Output signals 2-wire: 4 ... 20 mA others on request A permissible operating temperature of up to 85 °C and the possibility to use the device in intrinsic safe areas enable to measure the pressure of various fluids under extreme conditions. The basis for the LMK 458H is a capacitive ceramic sensor element, which offers a high overload resistance and medium compatibility. HART communication (setting of offset, span...

Open the catalog to page 13

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 15

Technical Data Technical Data IBExU 10 ATEX 1186 X zone 0 6: II 1G Ex ia IIB T4 Ui = 28 V, Ii = 93 mA, Pi = 660 mW, Ci = 105 nF; Li = 5 µH; Safety technical maximum values the supply connections have an inner capacity of max. 140 nF opposite the enclosure Permissible temperatures for environment in zone 0: -20 ... 60 °C with patm 0.8 bar up to 1.1 bar Connecting cables (by factory) cable capacity: signal line/shield as well as signal line/signal line: 160 pF/m cable inductance: signal line/shield as well as signal line/signal line: 1 µH/m for optional stainless steel pipe the following...

Open the catalog to page 15

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 16

Ordering code Output Seals Stainless steel 1.4404 (316L) Copper-Nickel-alloy (CuNi10Fe1Mn) customer Electrical connection Accuracy Cable length FKM EPDM FFKM customer PUR-cable 3 FEP-cable 3 TPE-cable 3 customer 0.1 % 5 customer in m Special version consult standard prepared for mounting with st. steel pipe 4 customer 1 nominal pressure ranges sealed gauge and absolute from 1 bar 2 mounting accessories are not part of supply and have to be ordered separately 3 shielded cable with integrated air tube for atmospheric reference 4 stainless steel pipe is not part of the supply 5 only possible...

Open the catalog to page 16

HYDROSTATIC PROBES SCREW-IN TRANSMITTER - 17

LMK 358H Separable Stainless Steel Probe with HART®-communication Ceramic Sensor accuracy according to IEC 60770: 0.1 % FSO Nominal pressure from 0 ... 60 cmH2O up to 0 ... 100 mH2O Output signals 2-wire: 4 ... 20 mA others on request Special characteristics ► diameter 39.5 mm ► cable and sensor section separable ® ► HART communication (setting of offset, span and damping) ► permissible temperatures up to 85 °C ► high long-term stability Optional versions ► IS-version zone 0 ► cable protection via corrugated pipe The separable stainless steel probe LMK 358H has been...

Open the catalog to page 17