DPT 200 Differential Pressure Transmitter for Process Industry with HART®-Communication accuracy according to IEC 60770: 0.075 % FSO Differential pressure The differential pressure transmitter DPT 200 has been especially designed for the process industry and can be used for level measurement of closed, pressurized tanks, pump or filter controlling, etc. from 1 mbar up to 20 bar Static pressure max. 400 bar DPT 200 can be equipped with various chemical seals and different membrane materials to reach an optimal adaptation to the application. Preferred areas of use are Special characteristics Oil and gas industry static over pressure 400 bar aluminium die cast case Energy industry output signal: linear or square root extraction Chemical and petrochemical industry Optional versions Paper industry Ex-version group I - Ex ia = intrinsically safe version for firedamp mines Ex-version group II - Ex ia = intrinsically safe version - Ex d = flameproof enclosure stainless steel housing BD SENSORS GmbH BD-Sensors-Straße 1 D - 95199 Thierstein

DPT 200 Differential Pressure Transmitter Differential pressure ranges Sensor type Differential pressure range dp Setting limits (offset and span in this range freely adjustable) Lowest permissible span Permissible static pressure optional Rangeability TD (with respect to the differential pressure range dp) 1 Technical Data only possible in combination with process connection (code N20), without valve (code 0) and with PTFE seal (code 4) Output signal / Supply Standard Option IS-version Error signal Namur NE43 Performance Accuracy 2-wire: 4 ... 20 mA with HART® communication / VS = 16.5 ... 42...

DPT 200 Differential Pressure Transmitter Materials Pressure port / flange Housing Cable gland Vent and dump valves, blanking plugs, type plate Bolts and nuts Seals Technical Data stainless steel 1.4401 (316) others on request standard: aluminium die cast with epoxy painting (blue) option: stainless steel 1.4301 (304) others on request aluminium die cast housing: PA grey (for cable-Ø 5 … 9 mm) stainless steel housing: stainless steel 1.4404 (316L) (for cable-Ø 7 … 12 mm) option IS-version: specified under ″Explosion protection″ stainless steel 1.4401 (316) steel, zinc flake coated standard: FKM...

DPT 200 Differential Pressure Transmitter Pin configuration Electrical connection Supply + (Vs +) Supply / Test – (Vs –) Test + Technical Data terminal clamps (for cable-Ø max. 2.5 mm²) + TEST + Ground Dimensions (mm / in) DPT 200 with display pressure measurem

DPT 200 Differential Pressure Transmitter Technical Data Process connections code N20 / N25  In scope of delivery two locking screws 1/4" - 18 NPT are included as standard.

DPT 200 Differential Pressure Transmitter Technical Data Valves (optionally) code 1 vent position: straight (2x) vent position: bottom (2x) pressure measurement

DPT 200 Differential Pressure Transmitter Accessories Technical Data Oval flange adapter 1/2" NPT female Technical data Material of adapter stainless steel 1.4401 (316) Weight approx. 300 g Scope of delivery two adapter, four locking screws 7/16 UNF x 1 3/4" A2 Ordering type Ordering code Oval flange adapter with 1/2" NPT female Z1004181 Oval flange adapter M20x1.5 male with tube Ø 13 mm (optionally with volume reduced flange - code N25) Technical data Material of adapter / tube stainless steel 1.4401 (316) Weight approx. 250 g Scope of delivery two adapter, four locking screws 7/16 UNF x 1"...

DPT 200 Differential Pressure Transmitter Technical Data Accessories Mounting bracket including U-bracket for pipe mounting: Technical data Material of mounting bracket Weight Scope of delivery Ordering type Mounting bracket pressure measurement stainless steel 1.4301 (304) approx. 500 g mounting bracket, four locking screws 7/16 UNF x 3/4" A2, U-bracket for pipe mounting with two nuts and washers Ordering code Z1004179

DPT 200 Accessories Technical Data Differential Pressure Transmitter Mounting variants for mounting bracket © 2024 BD|SENSORS GmbH – The specifications given in this document represent the state of engineering at the time of publishing. We reserve the right to make modifications to the specifications and materials. wall mounting pipe mounting HART® is a registered trademark of HART Communication Foundation; Hastelloy® is a brand name of Haynes International Inc. www.bdsensors.de [email protected]

Accessories oval flange adapter 1/2" NPT female optionally with N25 oval flange adapter M20x1.5 male with tube mounting bracket in stainless steel 1.4301 (304) only possible in combination with process connection (code N20), without valve (code 0) and with PTFE seal (code 4) only in combination with aluminium housing only in combination with stainless steel housing only in combination with process connection (code N20 or N30) HART® is a registered trade mark of HART Communication Foundation; Hastelloy ® is a brand name of Haynes International Inc. © 2023 BD|SENSORS GmbH - The specifications given...