Catalog excerpts
Mono-Block Stainless Steel Pressure Sensors SEIZOR The 330B is a mono-block pressure sensor made from 304 stainless steel via BCM thick-film technology. Thanks to the mono-block structure, there is no O-ring needed as seal inside the sensor body and no leakage can happen at the back of the sensor. By means of thick film technology, the resistor network including the Wheatstone bridge circuit and the compensation circuit is directly printed at the back of the 304 stainless steel pressure diaphragm. The other side of the diaphragm is exposed to measured media without For specific request, the sensor can be equipped with signal conditioning circuit to have amplified output • rugged mono-block structure • either with or without temperature compensation • impact and vibration resistance • easy mounting liquid level control • process control systems • hydraulic controls • biomedical instrumentation Environmental Specifications position effect: < 0.1% of zero offset shift vibration effect: no change at 10 g (RMS), BCM SENSOR TECHNOLOGIES BVBA Industriepark Zone 4, Brechtsebaan 2 Tel.: +32-3-238 6469 website: www.bcmsensor.com B-2900 Schoten - Antwerpen, BELGIUM Fax: +32-3-238 4171 email: sales@bcmsensor.co
Open the catalog to page 1
Mono-Block Stainless Steel Pressure Sensors Technical Data General conditions for measurements: media temp. = 25°C ±1°C, ambient temp. = 25°C ±1°C, humidity = 50%RH ±10%RH, barometric pressure: 86-106 kPa, vibration = 0.1 g (1m/s/s) max. Notes: 1. The pressure medium should be compatible with wetted parts material and pressure diaphragm. 2. For customized pressure ranges, consult BCM. 3. "fs" refers to full scale pressure or rated pressure. 4. Options for the output signal: 0.5~4.5Vdc ratiometric, 4~20mA, l2C, SPI. 6. Calculated as a rate of output change between 25°C and 70°C, and...
Open the catalog to page 2
Mono-Block Stainless Steel Pressure Sensors Ordering Information pos. 2: pressure ranges and references SP: solder pads (standard for mV output) FW: flying wires, PVC, 100mm (standard for 0.5/4.5V, 4/20mA, "(*)" is necessary only if any customized parameter is required, otherwise it is neglectable. Examples of Ordering Code • standard sensor: • customized sensor: BCM SENSOR TECHNOLOGIES BVBA Industriepark Zone 4, Brechtsebaan 2 Tel.: +32-3-238 6469 website: www.bcmsensor.com B-2900 Schoten - Antwerpen, BELGIUM Fax: +32-3-238 4171 email: sales@bcmsensor.com
Open the catalog to page 3All BCM SENSOR TECHNOLOGIES bv catalogs and technical brochures
-
EPS200-series3 Pages
-
model 328s2 Pages
-
664F(C)3 Pages
-
101B(A19F)4 Pages
-
101B(A12.6H)4 Pages
-
101B(a19L)4 Pages
-
Model 101B (a19D)3 Pages
-
Model 1966/19963 Pages
-
Model 18113 Pages
-
WD 21 Weighing indicator1 Pages
-
153T3 Pages
-
670F3 Pages
-
725F4 Pages
-
FD1013 Pages
-
119B3 Pages
-
Model 15313 Pages
-
Model 2 9 6 53 Pages
-
M o d e l 1 9 1 6 / 1 9 9 63 Pages
-
Model 18152 Pages
-
Model 181 13 Pages
-
Model A32 Pages
-
Model A22 Pages
-
Model T30005 Pages
-
model 3911/39913 Pages
-
Model 16613 Pages
-
Model 16603 Pages
-
Semiconductor Strain Gauges5 Pages
-
Model TFS21003 Pages
-
Model TFS22003 Pages
-
Model TFS20003 Pages
-
Model L V66(a)/L V66(b)4 Pages
-
Model L V382 Pages
-
Model L V393 Pages
-
Model L V371 Pages
-
Model L V363 Pages
-
Model L V351 Pages
-
Model L V163 Pages
-
Model 101B(f)6 Pages
-
Model 101B(a15G)4 Pages
-
Model 101B(a13H)4 Pages
-
Model 101B(a12.6L)4 Pages
-
Model 664F(b)3 Pages
-
Model 664F(a)3 Pages
-
Model 301B4 Pages
-
Model 500G4 Pages
-
Model SE1063 Pages
-
Model SE1053 Pages
-
Model SE1034 Pages
-
Model SE1024 Pages
-
Model SE1013 Pages
-
BCM Load Cells2 Pages
