Series 400
7Pages

300 Series - Art.No. 1134, 1135, 1146, 1147, 1148, 1149_V2 table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:10.00pt "Times New Roman", serif; } .font1 { font:15.00pt "Times New Roman", serif; } .font2 { font:22.00pt "Times New Roman", serif; } .font3 { font:14.00pt "Verdana", sans-serif; } Bamberg + Bormann ELECTRONIC GmbH INSTRUCTION MANUAL MOVISTROB® Series 400 Type 400.00 / 400.01 / 420.00 BBE Bamberg + Bormann - Electronic GmbH WiebelsheidestraBe 45 D-59757 Arnsberg / Neheim-Hsten Tel.: 0049 (0)2932-547760 Fax: 0049 (0)2932-34675 Internet: http://www.bbe-electronic.de e-mail: info@bbe-electronic.de

300 Series - Art.No. 1134, 1135, 1146, 1147, 1148, 1149_V2 table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:9.00pt "Times New Roman", serif; } .font1 { font:11.00pt "Times New Roman", serif; } L Introduction Each MOVISTROB® product has to pass through various controls during its production phases and must also undergo very strict and conscientious function and quality tests before leaving the factory for delivery to our clients. We can assure you that the MOVISTROB® product you received is in strict conformity with our high quality standards and it fully meets...

300 Series - Art.No. 1134, 1135, 1146, 1147, 1148, 1149_V2 table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:7.00pt "Times New Roman", serif; } .font1 { font:9.00pt "Times New Roman", serif; } .font2 { font:11.00pt "Times New Roman", serif; } The instrument may be operated by trained personnel only. Maintenance and repairs may also be carried out by qualified personnel or by the manufacturers only. 3. Controls and Indicators The instrument carries the following controls and functional components (see fig.): 3J_ SIGNAL MAINS PUSHBUTTON "ON" ( 1 ) switches on the...

300 Series - Art.No. 1134, 1135, 1146, 1147, 1148, 1149_V2 table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:7.00pt "Times New Roman", serif; } .font1 { font:9.00pt "Times New Roman", serif; } .font2 { font:11.00pt "Times New Roman", serif; } The response cycle lies at 2,5 V (TTL). Caution: Always press the proper "Frequency Range Selector Button" (3) for the flash frequency range in which the external synchronization frequency lies. In any case if the control impulse frequency exceeds the preselected low range the next higher range should be selected as a...

300 Series - Art.No. 1134, 1135, 1146, 1147, 1148, 1149_V2 table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:9.00pt "Times New Roman", serif; } .font1 { font:11.00pt "Times New Roman", serif; } as a working range. However, in order to avoid an overloading of the flash bulb we recommend you initially select the highest range (80 Hz to 300 Hz) in such cases. The maximum permissible permanent flash rate (18000 RPM) may be exceeded for short periods (not more than 1 minute) up to maximum flash rate of 30000 RPM. Do not allow the flash bulb to burn constantly. 5....

300 Series - Art.No. 1134, 1135, 1146, 1147, 1148, 1149_V2 table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:9.00pt "Times New Roman", serif; } .font1 { font:11.00pt "Times New Roman", serif; } If we compare this with the true angular speed of the object, we obtain: w' = (e -s- n ) w For e > 0 (i.e. T > Tn and/or f > fn) w and w' have the same sign, so that true and apparent rotation are in the same direction. The opposite holds for e < 0. With increasing /e/ the angular speed w' of the apparent rotation rises. Finally the angle 2pe becomes so large that the...

300 Series - Art.No. 1134, 1135, 1146, 1147, 1148, 1149_V2 table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:9.00pt "Times New Roman", serif; } .font1 { font:11.00pt "Times New Roman", serif; } 7. Maintenance and Repair If the instrument is suspected of being unsafe, take it out of operation permanently. This is usually the case when the unit shows physical demage, no sign of functioning or stress beyond the tolerable limits. Repair, replacing parts, calibration ect. should be carried out by trained personnel only or preferably return it to the manufacturer for...