Strip Heaters
12Pages

Strip Heaters Mica InsulatedU.L. Recognized-E56973 C.S.A. Certified - 016386-0-000 Construction 1 Post terminals. 2 Mica insulator. 3 Resistance Ribbon Wire. 4 Mica Element Support. 5 Rust Resistant Steel Sheath. Applications Dies, Cylinders, Kettles, Molds, Process Machines, Platens, Tanks, or other applications where controlled heating is needed. Features • Strip heaters may be used single or in groups to provide the required amount of heat. • For maximum distribution, it is recommended that the strip heaters be clamped securely to the area to be heated to prevent distortion or unequal expansion. • Made in U.S.A. Web: www.hotwatt.com Email: sales@hotwatt.com 55

Strip HeatersMica Insulated ▼ Manfactured Items ▼ Overall Length Cat. No. Watts Watts Cat. No. Watts Watts Cat. No. Watts Watts Overall Length Cat. No. Watts Watts Cat. No. Watts Watts Cat. No. Watts Watts • Standard termination is Type SSA. For units under W wide, standard termination is Type FO. Wattages The above chart is based on a watt density of 30 watts per square inch of surface. The watt density should be varied, depending on operating temperatures in accordance with the following table. Operating Watts/square in. To compute wattage, multiply length (less 1") x width x watts per...

Strip Heaters Mica Insulated Optional Terminations Stainless Steel Post Up to 21⁄4" wide: 6-32 x 1" maximum, 5⁄8" on center. 21⁄4" wide and wider: 8-32 x 1" maximum, 3⁄4" on center. Type SSA: Parallel one end. High Temperature Insulated Leads Type FS: Insulated leads at one end. • Available on: 11⁄2" and wider. Type FO: Insulated leads at opposite ends. • Available on: 1" and wider. Type SSB: Tandem one end. • Available on: 11⁄2" and wider. Type SC: Centered post terminals. • Available on: 11⁄2" and wider. Type SO: Opposite ends. • Available on: 1" and wider.

Strip HeatersCeramic Insulated U.L. Recognized-E56973 C.S.A. Certified - 016386-0-000 STRIP Applications Dies, Molds, Plastic Forming and Sealing. Tank and Kettle Heating. For specific applications, correctly rated elements should be used to prevent overheating and to ensure long life. A guide to correct watt densities for specific applications is shown on the next page. Features • The Hotwatt Stainless Steel Strip Heater provides clean, dependable heat with sheath temperatures up to 1200°F (649°C) and watt densities up to 40 watts per square inch. • Because of the seamless stainless steel...

Heated Length B” Hole Center “A” - OA Length Strip HeatersCeramic InsulatedStandard Termination Type OF: Offset at one end. 10-24 Terminals ▼ Manfactured Items ▼ Min. Max. Cat.No. "A" "B" "C" Watts Watts Formulas for Determination of Watt Density Watts/sq in = Total unit wattage C (heated length) x 3 Optional Terminations See page 61. • Maximum wattage limited by 18 amp maximum at 240 volts for catalog numbers CS-42.5 and longer. Any wattage is available between minimum and maximum without effecting price. • Unit lengths between and longer than those listed may be ordered. • Standard...

Strip HeatersCeramic Insulated ▼ IN STOCK ITEMS ▼ Strip Heaters - Stainless steel sheath Supplied with: Type OF terminals, except CS-5.5, which is SSA U.L. Recognized — E56973 C.S.A. Certified - 016386-0-000

Strip HeatersCeramic InsulatedOptional Terminations Type SSA: Parallel at one end. Heated length ("C”) is X" longer Type SF1: Flexible high temperature insulated leads. Specify length. Opposite end of unit may be standard closure with mounting hole or any of the optional cbsures. (Blunt end, XS54, shown.) Suitable for use to 480V. Lead end may be sealed for moisture resistance. Optional End Closures XS-54: Blunt end. Welded each end with no mounting holes. May be used with Type OF, SSA, or SO terminals. Heated length ("C") is 3* longer. XS-84: Secondary insulating bushings. Required when...

Strip Heaters Ceramic Insulated Finned Air Heating, Air Ovens, Load Banks. Construction 5 1 Seamless stainless steel sheath. 6 2 Post terminals. 3 Ceramic element support. 4 Element wire situated in close proximity to outside surface for Magnesium oxide packing. Aluminum fins offering maximum radiating surface and providing for rapid heat transfer to the surrounding medium. Stainless steel fins are available for corrosive environments. Aluminum fins are standard. maximum heat transfer and minimum internal temperature while preserving good dielectric qualities.

Strip HeatersCeramic Insulated Finned Type Max. Watts/ Min. Max. Cat.No. "A" "B" "F" Watts Watts Total unit wattage F (finned length) x 3 • Maximum wattage limited by 18 amp maximum at 240 volts for catalog numbers FS-35.7 and longer. Any wattage is available between minimum and maximum without effecting price. • Lengths between and longer than those listed may be ordered. Standard Termination Web: www.hotwatt.com Email: sales@hotwatt.com 63

Strip HeatersCeramic Insulated Finned ▼ IN STOCK ITEMS ▼ Strip Heaters - Seamless stainless steel sheath Supplied with: Type OF terminals, aluminum fins U.L. Recognized-E56973 C.S.A. Certified - 016386-0-000

Strip Heaters Ceramic Insulated Finned Optional End Closures XS-54: Blunt end. Welded each end with no mounting holes. May be used with Type OF or SSA terminals. Finned length (“F”) is 3" longer. XS-83: Short crimp. At each end with no mounting holes. May be used with Type OF or SSA terminals. Finned length (“F”) is 1" longer. XS-85: Stainless steel fins. For use in corrosive environments. XS-84: Secondary insulating bushings. Required when units are connected in series on voltages above 300V. Sheath must be isolated. Requires enlarged (1⁄2" x 3⁄4") mounting hole each end. May be used with...