MODEL 2091 TYING MACHINE OPERATOR MANUAL The Original Package Tying Machine B. H. Bunn Company 2730 Drane Field Rd., Lakeland, Florida 33811-1395 Telephone: 863/647-1555 Toll Free: 800/222-BUNN Fax: 863/686-BUNN Website: www.bunntyco.com

BUNN TYING MACHINE SERIAL # Notice Do not attempt to operate this Equipment before reading the operation instructions and performing the Before Operation Checks paragraph in section 3 of this manual. OPERATOR SAFETY REMINDERS The National Safety Council reminds us  that most accidents are caused by the failure of some individual to follow simple and fundamental safety rules or precautions. For this reason, you as a careful operator, are the best insurance against an accident.  Regardless of the care used in the design and construction of any type of equipment there are many conditions that...

Tying Machine Operator Manual Foreword This manual contains instructions for installation, operation, preventative maintenance, troubleshooting and repair parts identification for your tying machine manufactured by the B. H. Bunn Company, Lakeland, Florida. Proper use of the manual should ensure safe and efficient operation and maintenance of the tying machine. Because of the increasing staff of Service Representatives, B. H. Bunn Company can now offer a Maintenance Contract. Contact your local service representative, who is capable to render factory approved service, for full details maintenance...

Section I - Introduction Purpose of Tying Machine The primary purpose of the tying machine is to automatically tie mail, packages, cartons, piece parts, printed matter, newspaper, laundry, produce, meats, corrugated cardboard and miscellaneous materials and products requiring a secure wrap (figure 1). The tying machine ties almost everything that was previously wired, banded, taped, strapped, tied by hand in offices, factories and commercial establishments. The tying machine reduces tying time, employee effort and fatigue, reduces twine lint and waste, enables trained operators to make secure...

Section I – Introduction Continued Simultaneously, the twine arm is continuing its arc and the knotter body turns counter clockwise opening the jaw for the two strands of twine which are wrapped around the knotter body assembly. The strands of twine are brought through the jaws and the jaws firmly lock. The knotter body assembly then moves towards its finished position and the stripper forces the twine strands off the knotter body jaws, into the tight part of the knot. As the two strands of twine are pulled into loops from the knotter body assembly jaws, the knifetrap moves forward and cuts a...

Single Wrap — The arm carries the twine arm around once and the knot is formed. Double Wrap — One Way Two wraps in one direction with one knot. Triple Wrap — One Way Three wraps in one direction with one knot. Double Wrap* — Cross Tie One wrap in each direction with only one knot. Triple Wrap** — Cross Tie One wrap in one direction; Two wraps in other direction — with only one knot. ** Triple wrap cross tie additionally provides: (1) Three * Double wrap cross tie also provides: (1) two wraps in wraps in one direction if package is not turned between one direction if package is not turned between...

Section II - Preparation For Use Uncrating instructions 1. Cut bands securing the carton to the skid. 2. Cut the bottom of the cardboard carton where it is secured to skid. 3. Carefully raise and remove the carton from the tying machine. 4. Carefully remove the steel strapping from the machine and then pull the tying machine away the skid. 5. Remove the box in the twine container shipped with the tying machine containing four casters. 7. Using the casters shipped with the tying machine, insert a caster into the caster socket on each leg of the tying machine. Note: pany The manual should be wrapped...

Threading Procedures Before the tying machine is shipped, it is threaded through each guide starting from the twine container to the stringholder button. To avoid threading problems in the future, you should become familiar with the threading sequence at this time. Complete threading of the tying machine can be avoided if the end of the twine or tape being used is caught before it leaves the twine container. This is accomplished by simply tying the end of the existing twine or tape to the starting end of the new twine or tape with a square knot. If the end of the twine or tape is not caught before...

Before Operation Checks 1. Turn “ON-OFF” switch to the “OFF” Position. 2. Check for proper threading. 3. Check if twine or tape cone is properly seated on foam pad of twine container. 4. Check twine running tension by pulling twine from end of twine arm assembly. A smooth easy running tension should be felt. 5. Visually check the tying machine for any mechanical defects or missing parts. Tying Size Limitations The capacity graph on the Model Characteristics Sheet at the front of the manual indicates the maximum height and width of the packages that can be tied. Bunn tying machines adjust automatically...

Section IV – Maintenance Lubrication Requirements ARROWS IN PHOTOS IDENTIFY OIL HOLES AND LUBRICATION POINTS Please refer to Lubrication / Maintenance for frequency. Knotter Head Front Rear Main shaft, Clutch shaft Main Table, Clutch Fork, Kickout Wedge. Knotter Head Side View, Dual Tension, Knife Trap Front Frame Main Shaft, Drawslide Lever Main Table

A good preventative maintenance program is a major step forward to assure trouble-free tying machine operation. In order to be effective, routine inspection, lubrication and adjustment schedule must be established and followed. For tying machines subjected to normal usage which is considered to be approximately 30 hours of operation weekly, the following maintenance and lubrication schedule should be followed. Substantial deviations from normal usage should require an adjustment in the indicated frequencies. The Lubrication Requirement has frequencies of 50 and 150 hours. The following mechanical...