video corpo cad

BTS series
7Pages

{{requestButtons}}

Catalog excerpts

BTS series - 1

• Ultra-slim width of only 7.2mm - W7.2xH18.6xL9.5mm (through-beam type) -W7.2xH24.6xL10.8mm (retroreflective type, convergent reflective type) • Detection methods and minimum target size - Through-beam type (BTS1M): 02mm - Retroreflective type (BTS200): 02mm (at distance 100mm) - Convergent reflective type (BTS15/BTS30): 00.15mm (at distance 10mm) * Detecting distance may vary by environmental factors • Maximum detection distance: 1m (through-beam type) • Stability indicator (red LED) and operation indicator (green LED) • Stainless steel 304 mounting brackets • IP67 protection structure (IEC standard) A Please read “Safety Considerations” in operation manual before using. Specifications Model (G) Connectors/ Connector Cables/ Sensor Distribution Boxes/Sockets (M) Tacho / Speed / Pulse Meters (Q) Stepper Motors & Drivers & Controllers 1: The sensing distance is specified with using the MS-6 reflector. The distance between the sensor and the reflector should be set over 0.1m. When using reflective tapes, the Reflectivity vary by the size of the tape. Please refer to the ' I Reflectivity by Reflective Tape Model’ table before using the tape. *2: Non-glossy white paper 50x50mm. *3: It will vary by the installation environment and sensing conditions. Please refer to the ‘© Conditions of min. sensing target and installations (retroreflective type)’. *4: The weight includes packaging. The weight in parenthesis is for unit only. *The temperature or humidity mentioned in Environment indicates a non freezing or

Open the catalog to page 1
BTS series - 2

• BTS1M-TDTL / BTS1M-TDTL-P • BTS200-MDTD / BTS200-MDTD-P Sensing area characteristic Measuring method © Retroreflective type• BTS200-MDTD / BTS200-MDTD-P Sensor angle characteristic • BTS30-LDTL / BTS30-LDTL-P Sensing area characteristic Measuring method

Open the catalog to page 2
BTS series - 3

Ultra-compact Amplifier Built-in Type Connections (B) Fiber Optic Sensors Load (black) Output ※1: Load connection for NPN output ※2: Load connection for PNP output (G) Connectors/ Connector Cables/ Sensor Distribution Boxes/Sockets (H) Temperature Controllers ● Convergent reflective type (I) SSRs / Power Controllers (brown) +V (black) Load ※1 Output (blue) 0V Load (brown) +V (black) Load ※1 Output (blue) 0V Load (L) Panel Meters (M) Tacho / Speed / Pulse Meters (N) Display Units Control Output Circuit Diagram NPN open collector output Photoelectric sensor circuit PNP open collector output...

Open the catalog to page 3
BTS series - 4

BTS Series Operation Mode Operation mode Received light Received light Interrupted light Receiver operation Interrupted light Transistor output Dimensions ● Through-beam type Optical axis of receiver Optical axis of emitter Stability indicator (green) ● Retroreflective type / Convergent reflective type Optical axis of emitter Stability indicator (green) Operation indicator (red) Optical axis of receiver Optical axis of emitter Optical axis of receiver Stability indicator (green)

Open the catalog to page 4
BTS series - 5

Ultra-compact Amplifier Built-in Type • Bracket B (sold separately)1.2 (A) Photoelectric Sensors 10 1.2 • Sub-bracket for through-beam type 1.2 3.2 6.7 11.2 k———w (D) Proximity Sensors (G) Connectors/ Connector Cables/ Sensor Distribution Boxes/Sockets • Sub-bracket for reflective type ^The sub-bracket for each sensing type is included bracket A (B). 1.2 (I) SSRs/Power Controllers • Reflector (MS-6) • Slit (BTS1M-ST, sold separately) • Reflective tape (sold separately) 01 (Q) Stepper Motors & Drivers & Controllers

Open the catalog to page 5
BTS series - 6

BTS Series Operating Timing Diagram High Stable light ON area Unstable light ON area Incident light level Unstable light OFF area Operation level Stable light OFF area Low Stability indicator (green LED) Transistor output ※ he waveforms of “Operation indicator” and “Transistor output” are for Light ON operation. T They are reversed for for Dark ON operation. Mounting and Sensitivity Adjustment Use M2 bolts to install this sensor, and keep the tightening torque under 0.3N.m. ※ xercise caution. Do not apply excessive impact to the E unit or bend the cable section. The inside unit may be wet....

Open the catalog to page 6
BTS series - 7

• Convergent reflective type Place the sensing target, then adjust the sensor up, down, left, right and fix the sensor at the center position where the stability indicator is operating. Make sure that the sensing side of the sensor is parallel to the surface of each object. S Accessory (sold separately)• Slit (model: BTS1M-ST) (A) Photoelectric Sensors • Min. sensing target and max. sensing distance by slit's 0 when attach the slit at an emitter. © Conditions of min. sensing target and installations (retroreflective type) When installing the retroreflective photoelectric sensor, be sure to...

Open the catalog to page 7

All Autonics catalogs and technical brochures

  1. BS5 series

    4 Pages

  2. BH series

    7 Pages

  3. MST series

    2 Pages

  4. BC Series

    7 Pages

  5. PR series

    10 Pages

  6. LE7M-2

    12 Pages

  7. SP Series

    4 Pages

  8. PT series

    4 Pages

  9. PRA Series

    4 Pages

  10. AS series

    2 Pages

  11. PR series

    6 Pages