video corpo cad

BS5 series
4Pages

{{requestButtons}}

Catalog excerpts

BS5 series - 1

-|Transparent Guide|- Groove-depth 9 mm Cable/Connector type Photomicro Sensors Safety Considerations • Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards. • ᜸ symbol indicates caution due to special circumstances in which hazards may occur. Failure to follow instructions may result in serious injury or death. 01. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic loss. (e.g., nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.) Failure to follow this instruction may result in personal injury, fire or economic loss. 02. o not use the unit in the place where flammable/explosive/corrosive gas, D high humidity, direct sunlight, radiant heat, vibration, impact, or salinity may be present. Failure to follow this instruction may result in explosion or fire. D 03. o not disassemble or modify the unit. Failure to follow this instruction may result in fire. D 04. o not connect, repair, or inspect the unit while connected to a power source. Failure to follow this instruction may result in fire. 05. heck ‘Connections’ before wiring. C Failure to follow this instruction may result in fire. Failure to follow instructions may result in injury or product damage. 01. se the unit within the rated specifications. U Failure to follow this instruction may result in fire or shortening the life cycle of the product. 02. se dry cloth to clean the unit, and do not use water or organic solvent. U Failure to follow this instruction may result in fire or electric shock. BS5 Series For your safety, read and follow the considerations written in the instruction manual, other manuals and Autonics website. The specifications, dimensions, etc. are subject to change without notice for product improvement. Some models may be discontinued without notice. • Select appearance depending on the install location (K, T, V, L, Y, F, R, TA type) • Minimize malfunction and improve visibility - Minimize sensing part, gap and flush of the body to reduce malfunctions caused by a foreign substance - Built-in U-shaped indicator can be checked in many directions • Selectable models for the operation of indicator - Indicator turns ON under the light received condition - Indicator turns ON under the light interrupted condition • Resistant structure for shock and vibration - Shock 15,000 m/s2 (approx. 1,500 G), vibration 10 to 2,000 Hz (1.5 mm amplitude) • Selectable operation modes (Light ON/Dark ON) via connector or control wire • High-frequency response : 2 kHz • Follow instructions in ‘Cautions during Use’. Otherwise, It may cause unexpected accidents. • Use the product, 0.5 sec after supplying power. When using separate power supply for the sensor and load, supply power to sensor first. • 5-24VDCᜡ power supply should be insulated and limited voltage/current or Class 2, SELV power supply device. • Wire as short as possible and keep away from high voltage lines or power lines, to prevent inductive noise. • When using sensor with the equipment which generates noise (switching regulator, inverter, servo motor, etc.), ground F.G. terminal of the equipment. • This unit may be used in the following environments. - Indoors (in the environment condition rated in ‘Specifications’) - Altitude max. 2,0

Open the catalog to page 1
BS5 series - 2

Connections This is only for reference. For selecting the specific model, follow the Autonics web site. BS 5 - O © - © ■ Cable type O Appearance+Connection Connector type ■ Connector type Brown Blue White • For LOAD connection, follow the cable type connection. • Be sure to connect the unit using the dedicated socket (CT-01 or CT-02, sold separately). If it is soldered on the unit terminal pin directly not using the connector socket (CT-01), it may cause product damage. ■ Selectable operation mode Operation mode Inner Circuit■ NPN open collector output ■ PNP open collector output • OCP...

Open the catalog to page 2
BS5 series - 3

Specifications Series 01) Response frequency is the value getting from revolving the circle panel below.

Open the catalog to page 3
BS5 series - 4

-|Transparent Guide|- Sockets (Sold Separately) • Unit: mm, for detailed dimensions, visit our website. 18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002 www.autonics.com | +82-51-519-3232

Open the catalog to page 4

All Autonics catalogs and technical brochures

  1. BH series

    7 Pages

  2. MST series

    2 Pages

  3. BTS series

    7 Pages

  4. BC Series

    7 Pages

  5. PR series

    10 Pages

  6. LE7M-2

    12 Pages

  7. SP Series

    4 Pages

  8. PT series

    4 Pages

  9. PRA Series

    4 Pages

  10. AS series

    2 Pages

  11. PR series

    6 Pages