Prehenseur de grandes precision & rigidite Series HFC1 Respect de I'envirornne' Produit conforme BlaWS RoHS Compliant Product

High-Rigidity, High-Precision Air Hand Dimensions Model Open/closed stroke Mass (height X width X length) mm m

Before use, be sure to read the “Safety Precautions”. The illustration shows HFBDP16M of the HFB series l guide specification. The photograph shows HFC1D16M. Reduced Reduced • Reduced in width, length, and height. • About 45% more compact by volume than the HFB series linear guide specifications. (Comparison with previous Automax products) ReducedEmbedded sensor switches (optional) Length Vertical lead wire Horizontal lead wire HFC1 Series provides high performance and high rigidity despite its smaller size. Repeatability ± 0.01mm [± 0.0004in.] or less. Centering accuracy ± 0.07mm [± 0.0028in.]...

Remark:R is the distance from the main body end to the gripping point. | Gripping | 1. When attaching fingers on the levers, design them as short and as light as possible. If the fingers are longer and heavier, the impact force when opening and closing will increase and cause a decrease in the gripping accuracy and/or wear and damage to the sliding portion. Also, to prevent the workpiece from falling down or being damaged, and to reduce the metal contact noise when gripping, plastic or rubber materials should be attached to the fingers at the parts of contact. In cases with long gripping point...

Selection Effective gripping force Gripping point limit range Gripping point distance L mm Workpiece gripping point ：Closed side Gripping point distance L (mm) Gripping point distance L (mm) Effective gripping force F (N) Gripping point distance L (mm) Effective gripping force F (N) Effective gripping force F (N) Gripping point distance L (mm) Effective gripping force F (N) Gripping point distance L (mm) Gripping point distance L (mm) Gripping point distance L (mm) Gripping point distance L (mm) 1mm = 0.039in., 1MPa = 145psi.

HFC1 SERIES Specifications Note: 1. Values are obtained when gripping point distance is 30mm [1.18in.] under operating pressure 0.5 MPa [73psi.]. For details of the effective gripping force, see the graphs on p. . Inner Construction Major Parts and Materials No. Order Codes Operating type D : Double acting type Sensor switch Blank : Without sensor switch XEZE1D:2-lead wire solid state type with indicator lamp Horizontal lead wire DC10 - 28V XEZ31D: 3-lead wire solid state type with indicator lamp Horizontal lead wire DC4.5 - 28V XEZE1L:2-lead wire solid state type...

HFC1D10M HFC1D16M M5X0.8 (Connection port for opening) 4-M4X0.7 (Both sides) Drilled through hole\ p3.4

(Connection port for closing)x 4-M6X1 (Both sides) Drilled through hole' ^5.1

SENSOR SWITCHES Solid State Type Order Codes Sensor switches only for HFC1D with lead wire length: 3000mm Sensor switch XEZE1D: 2-lead wire solid state type with indicator lamp XEZE1L: 2-lead wire solid state type with indicator lamp XEZ31D: 3-lead wire solid state type with indicator lamp XEZ31L: 3-lead wire solid state type with indicator lamp DC10 ~ 28V Horizontal lead wire DC10 ~ 28V Vertical lead wire DC4.5 ~ 28V Horizontal lead wire DC4.5 ~ 28V Vertical lead wire Solid state type Model Load voltage Load current Item Wiring type Lead wire direction Consumption current Internal voltage drop...

Distance sensor switch allowed to protrude The maximum distance that the sensor switch protrudes from the body end surface (when the levers are completely closed) is as shown in the table below. Use these values for Confirm the levers are completely closed. jrm 2 Push the switch into the groove on the body in the direction of the arrow. 3 By moving the switch in the direction of the arrow, the lamp turns ON. ami 4 Secure the sensor switch by the mounting screw after moving it about 0.3 mm further in the direction of the arrow from where the lamp turned ON in e . 1 Confirm workpiece is externally...

Points of Wiring Solid State Type Sensor Switches 2-lead wire type Basic connection Brown Sensor switch Basic connection Load DC10?28V Connection with relays Brown Black Blue Sensor switch Connection with relays Brown Sensor switch AND (series) connection and OR (parallel) connection Relay Sensor switch Sensor switch AND (series) connection and OR (parallel) connection Sensor switch Sensor switch Sensor switch Connection with TTL Separate connection Sensor switch Sensor switch Relay contact Sensor switch Relay contact Relay contact Sensor switch Load Connection with solenoid valve Connection...