Exhibit with us
*mydirectindustry  
English
  1. Catalogs
  2. August Handel GmbH - CARFIT
  3. Thermo Paint Spray 650°C

Thermo Paint Spray 650°C

Thermo Paint Spray 650°C
1 / 1 PageView full catalog

Thermo Paint Spray 650°C

Product catalog summary
Description: The document describes a high-quality, heat-resistant black paint spray designed for parts exposed to high temperatures, such as exhaust pipes, engines, and chimneys. It is based on silicone resin and can withstand temperatures up to 650°C.
Application: Suitable for metal surfaces, the paint is ideal for automotive and motorcycle parts, as well as chimneys. It offers fast drying at room temperature, good coverage, flow, and resistance to mechanical and weather effects.
Characteristics: The paint is fast-drying, with a temperature resistance of up to 650°C. It provides very good coverage, high mechanical resistance, and good weather resistance.
Technical Data: The paint should be applied in two coats, with a consumption rate of one spray can per approximately 1 – 1.2 m². Drying times vary based on environmental conditions, with dust dry in about 10 minutes and touch dry in 15 minutes. It can be exposed to high temperatures after about 1 hour.
Substrate Pretreatment: Surfaces must be cleaned and degreased with C.A.R.FIT Silicone Remover, old coatings removed, and corrosion spots sanded. Sandblasting is recommended, followed by another cleaning and drying. A suitable primer is recommended for better adhesion.
Storage and Handling: The spray should be applied at a distance of 25 cm and at room temperature, ideally between 15 – 25°C. The can should be shaken before each coat, and the nozzle cleaned after use. Maximum heat and fuel resistance are achieved after stoving at 160 – 200°C for about 30 minutes. The container should not be exposed to direct sunlight or stored above 35°C.
See more

Catalog excerpts

Thermo Paint Spray 650°C-1

Thermo Paint Spray 650°CDESCRIPTION High quality heat-resistant black paint spray is used for treating parts exposed to high-temperature heating. For coats of exhaust pipes and engines of cars and motorcycles as well as for chimneys and etc. • Fast drying at room temperature • Very good coverage • Good flow • High mechanical resistance • Good resistance to weather effects All kinds of metal surfaces. SUBSTRATE PRETREATMENT • Clean and degrease the surface with C.A.R.FIT Silicone Remover • Remove old coating and sand corrosion spots with grit P80 - P240 • Sand blast the surface • Again clean and degrease the surface with C.A.R.FIT Silicone Remover and thoroughly dry it Shake thoroughly for at least 2 min Flash-off between layers: 3 - 5 min • Do not apply on chrome-plated surfaces • Apply at room temperature. Optimal application temperature: 15 - 25°C • Shake the spray can once more before application of each new coat • After use, hold aerosol can upside down and spray briefly to clean the nozzle • Maximum heat-resistance and fuel-resistance is achieved after stoving at 160 - 200°C for ca. 30 min FURTHER TREATMENT • dust dry: ca. 10 min • dry to touch: ca. 15 min • can be exposed to high temperature: after ca. 1 h Drying time depends on environment temperature, humidity and coating thickness TECHNICAL DATA Temperature resistance silicone resin black This is a pressurized container, do not expose to direct sunlight or store above 35°C

 Open the catalog to page 1

All August Handel GmbH - CARFIT catalogs and technical brochures

  1. 2K HS Acryl Primer Filler 4:1
    2K HS Acryl Primer Filler 4:1

    1  Page

  2. Fillable Spray Can
    Fillable Spray Can

    1  Page

  3. Fade-out Thinner Spray
    Fade-out Thinner Spray

    1  Page

  4. Underbody Protection Bitumen Spray
    Underbody Protection Bitumen Spray

    1  Page

Archived catalogs

  1. Carbon Putty
    Carbon Putty

    1  Page

  2. 2K Epoxy Primer 1:1
    2K Epoxy Primer 1:1

    1  Page

  3. C.A.R.FIT Katalog
    C.A.R.FIT Katalog

    76  Pages

  4. Spray Putty
    Spray Putty

    1  Page

  5. 2K Ultra HS Clear Coat
    2K Ultra HS Clear Coat

    1  Page

  6. Fade-out Thinner Spray
    Fade-out Thinner Spray

    1  Page

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.
About DirectIndustry
DirectIndustry is a marketplace that offers B2B players a complete experience, from product sourcing to purchase. DirectIndustry is an entity of VirtualExpo Group.
Are you a buyer?
Are you a supplier?
About Us