ATA5577M1330C-PPMY Read/Write LF RFID IDIC Transponder 125KHz DATASHEET Identification transponder in plastic brick package Includes ferrite coil for tuned circuit antenna Basic component: Atmel® ATA5577M1330C IDIC® Contactless power supply Contactless downlink data transmission Radio frequency fRF = 125kHz 363-bit EEPROM memory in total: 11 blocks × (32 Bits + 1 lock-bit) ● 7 × 32 Bits EEPROM user memory including 32-bit password memory ● 2 × 32 Bits unique ID ● 1 × 32-bit option register in EEPROM to set up the analog front end: ● Clock detection level ● Gap detection level ● Improved downlink timing ● Clamp voltage ● Modulation voltage ● Soft modulation switching ● Write damping like the Atmel T5557/ATA5567 or with resistor ● Downlink protocol ● 1 x 32-bit configuration register in EEPROM to set up: ● Data rate: ● RF/2 to RF/128, binary selectable or ● Fixed basic mode rates ● Modulation/coding: ● ASK, FSK, PSK, Manchester, bi-phase, NRZ ● Other options: ● Password mode ● Max block feature ● Direct access mode ● Sequence terminator(s) ● Block-wise write protection (lock bit) ● Answer-on-request (AOR) mode ● Inverse data output ● Disable test mode access ● Fast downlink (~6Kbits/s vs. ~3Kbits/s) ● OTP functionality ● Init delay (~67ms)

Description The Atmel® ATA5577M1330C-PPMY is a contactless read/write identification transponder (IDIC®) for applications in the 125kHz frequency band. It consists of a plastic brick which accommodates the read/write IDIC ATA5577M1330C. The antenna comprises an inductor which in combination of the on-chip capacitor serves as power supply and bi-directional communication interface. The on-chip 363-bit EEPROM (11 blocks with 33 bits each) can be read and written block-wise from a base station (reader). Two dedicated blocks are reserved for setting the IDIC operating modes. Another block may be...

General The transponder consists of a plastic brick which accommodates the following components: ● Atmel® ATA5577M1330C Read/Write IDIC® Coil with Ferrite Core The antenna is implemented as a tuned inductor Transponder Antenna The antenna consists of a coil and an on-chip capacitor of Atmel ATA5577M1330C for tuning the circuit to the nominal carrier frequency of 125kHz. The coil has a ferrite core for improving the distance of read, write and programming operations. Atmel ATA5577M1-PP Transponder Operation The Atmel read/write IDIC ATA5577M1330C is part of the Atmel transponder ATA5577M1330C-PPMY....

3. Absolute Maximum Ratings Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. i Type means: T: directly or indirectly tested during production; Q: based on initial product design

Measurement Assembly All measurements are done with commercial RFID reader/writer supplied by “GIS”. External antenna Figure 5-1. Testing Application Reader type: Antenna type: TS-A50-K1000, circular antenna, inner diameter 51mm, L = 1.08mH Ordering Information Available Order Codes ATA5577M1330C-PPMY Configuration on Delivery After Atmel® completes production, the transponder is configured as shown in Table 6-1. Unlike the ATA5577M1330C chip, the AFE option setup (block 3, page 1) is adjusted to the transponder operating mode suitable for most applications. All blocks in page 0 are not locked...

Package Information technical drawings according to DIN specifications 11/11/13 TITLE Package Drawing Contact: [email protected] Package: Transponder

Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 9333B-RFID-05/14 9333A-RFID-09/13 History • Section 4 “Electrical Characteristics” on page 4 updated • Section 5 “Measurement Assembly” on page 5 updated • New datasheet

XXXXXX Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA © 2014 Atmel Corporation. / Rev.: Rev.: 9333B–RFID–05/14 Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with...