ARNOLD Technology HIGH PERFORMANCE - METAL RECYCLING

Metal Recycling is not just Metal Recycling It is a well-known fact: metal recyc-ling is not just metal recycling. It is, above all, about enhancing the value of one’s metal residues through optimal metal recycling and the use of the optimum metal recycling technology. We are experts in this field. Like no other company we have specialised in optimal metal recycling technologies, based on the so-called Arnold-technology, which is well-proven worldwide. More than 80 years of experience in the field of metal processing and with more than 1,000 machines and equipment installed by our company – these...

Briquetting Press The ArnoBrik Series Briquetting Presses are offered with three different filling variants, according to the free flowing pro-perty of the material. An inclined feeder or a two-step feeder permit these presses to process both grinding slurry and drilling swarf. The solid welded construction design with two or three columns means that the machines can also be used for heavy continuous operation. Each machine can be operated manually or automatically. All presses have a graphic operator panel with visualisation of all process sequences and can therefore be integrated easily into...

Moving tool carriage The optimum system to balance the relative motion during the compression stage guaranteeing an enormous wear reduction in the pressing box. Briquetting Press Filling valve at the pressing cylinder ATM presses are pioneers on the market and set the trend. More than 30% of the drive energy can be saved by the use of the filling valve technology. 3-columns technology No other construction principle diverts pressing forces as effectively as the 3-columns technology. Columns fitted with patented clamping nuts process millions of compacting cycles at full load. Hydraulic tank The...

Recycling system of swarf processing From secondary raw materials to reusable briquettes. Special techniques Grinding slurry briquetting The most profitable aspect of briquette forming can be found during the briquetting process where more than 90% of the oil and water components are pressed out. The extruded lubricants and cutting oils can be reused. Due to the drop in expenses (no landfill charges and disposal costs) the investment in an ATM briquetting press is recovered within just a few months. Risk material magnesium or titanium shavings Stored titanium and magnesium swarf are highly inflammable....

Scrap Shear The ArnoCut Series Scrap Shear is produced in five sizes from 4,000 to 13,000 kN shear force. All compacting chamber wear plates are made of Hardox 450 up to Hardox 600 and guarantee the highest quality and a long useful life. Cutting cycles are optimised by path measurement systems in the cylinders. The need to use an elaborate foundation is avoided thanks to the monobloc construction. A centralized lubrication system, various clogging indicators and fault analysis guarantee simple maintenance. Comfortable operation with two joysticks and a multifunctional display in a soundproofed,...

Wear plates Depending on the purpose of the shear we offer straight wear plates as well as wear plates with special square or trapezoid-shaped profiles in various material qualities. Scrap Shear Ergonomic workplace An operator seat with 2 joysticks, monitor visualisation and video surveillance situated in an air-conditioned cabin set new standards in workplace design. ArnoCut for the cutting and pressing of light as well as heavy scrap. Traversing lateral compressor Two separately controllable side cylinders make it possible to traverse the side stamp up to 15° in order to pre-compress bulky...

Baling Press The ArnoPress K Series Baling Presses are available with 2 or 3 compactor steps. There are a total of five sizes in the programme. Models 100-2 to 600-2 compact in two steps, while models 100-3 to 350-3 compact the material three-dimensionally. All parts coming into contact with the scrap are lined with high-strength wear plates with a special wave-shaped profile. The solid welded construction design means that the machines can also be used for heavy continuous operation. The visualisation of all process sequences means that the systems can be integrated into fully automated production...

Wear plates Depending on the purpose of the press we offer wear plates with square-, trapezoid- and wave-shaped profiles in various material qualities. Baling Press PZT Pump activation technology The pump activation technology regulates the required quantity of oil per cylinder, thereby minimising the necessary drive energy of the press. Hydraulic tank The bicameral system guarantees the supply of filtered and cooled oil to the performance-controlled hydraulic pumps. ArnoPress K for the grouting of stamping waste resulting from series production. Bale carriage A patented bale carriage allows...

Recycling system of scrap baling From secondary raw material to bale. Supplementary equipment Tilting skip weighing scale To guarantee a controlled filling of the baling chamber a tilting skip weighing scale is employed to weigh the scrap. Scrap charge with emergency discharge Charging the scrap onto the press is carried out via conveyors. In case of service works on the press the scrap can be guided through an emergency discharge shaft. Strap hinge conveyor Bale carriage Your requirements For equipment employed in shift operation highly robust hinge plate conveyors are used. Special attention...

The ArnoPress D Series Baling Press can be supplied in five sizes. Models 80-2 and 100-2 compact on two levels, and models 100-3 to 300-3 compact the material three-dimensionally. The first compression is carried out using a cutting head, which allows bulky parts to be reduced in size as well as achieving pre-compaction. All parts coming into contact with the scrap are lined with high-strength wear plates with a special trapeze-shaped profile. Each machine can be controlled manually or automatically. Baling Press Functional criteria Because transport capacities to and from the scrap yard are...