1. Catalogs
  2. ATESTEO GmbH & Co. KG
  3. Manual steering wheel

Manual steering wheel

Manual steering wheel
1 / 21 PagesView full catalog

Manual steering wheel

Product catalog summary
Product Description
The measuring steering wheel by ATESTEO GmbH & Co. KG is designed for vehicle installation to measure steering torque and optionally the rotation angle. It can be mounted using an optional adapter kit or directly on the steering system. The product includes a torque sensor and an evaluation unit called VETAS. Proper handling is crucial to avoid damage or incorrect measurements.

Safety Instructions
Deactivate and remove the airbag before installation. Ensure the measuring steering wheel is securely mounted, and all screws are tightened to prevent disconnection and potential loss of vehicle control. The device is intended for test tracks only, not public roads. Protect the vehicle's 12 V power supply with fuses.

Equipment
The torque sensor includes electronics for measuring torque and angle, consisting of a rotor and stator. An optional adapter kit allows installation on the original steering wheel. A remote control is available for zero-point adjustment of torque or angle values.

Equipment Installation
With Adapter Kit: Follow vehicle manufacturer instructions to install the measuring steering wheel using the holder and clamping mechanisms.
Without Adapter Kit: Remove the airbag and original steering wheel, and mount the measuring steering wheel directly onto the steering system, often requiring a custom adapter.

Operation
Signal reset can be performed via remote control, terminal, CAN, or VETCO. Each method allows resetting the torque or angle measurement to zero.

Maintenance
Proper storage and regular calibration are necessary to maintain accuracy and functionality.

Safety Warnings
There is a risk of fatal injuries if the airbag is mishandled or if screws are not properly tightened, potentially leading to loss of steering control.

Equipment Installation
The torque sensor must be connected to a fixed part of the vehicle body for precise rotation angle measurements. Electrical installation involves connecting the torque sensor's wires to the VETAS3 evaluation unit.

Test Signal
The test signal is triggered via a terminal connected to a computer. Measured values should be compared with calibration data.

Operation
Operate using VETAS hardware and VECTO software. Follow safety instructions and do not exceed measurement ranges. Signal reset can be performed via remote control, terminal, CAN commands, or VECTO software.

Maintenance
Store the measuring wheel with screws inserted to prevent dirt ingress. Calibration should be done regularly, ideally every two years.

Appendix
Includes a table of figures and tables detailing components and their configurations.
See more

Catalog excerpts

Manual steering wheel-1

Measuring steering wheel Operating manual

 Open the catalog to page 1
Manual steering wheel-2

Measuring steering wheel V 2.3 11/2026 Change log: V2.3 17.11.2026: • Installation pictures added • Assembly and material overview added • Slight text updated V2.2 29.07.2024: • Information about the magnetic ring added to the equipment chapter • Chapters divided into equipment and equipment installation • Description of reset added • Remote control added as optional equipment V2.1 03.05.2022: • “Shunt calibration” replaced by “test signal” • Installation without adapter added • Difference between measurement body and adapter kit explained more clearly • Pictures of measurement body and cover...

 Open the catalog to page 2
Manual steering wheel-3

Measuring steering wheel - V 2.3 - 11/2026

 Open the catalog to page 3
Manual steering wheel-4

Product description Product description The product “measuring steering wheel” is used for installation inside of a vehicle. With an optional adapter kit it is mounted on top of the existing vehicle steering wheel. Without that adapter kit it can be mounted on the steering system after removing the original vehicle steering wheel. The “measuring steering wheel” measures the applied steering torque and optionally the rotation angle. The product must be handled as measurement sensor. Misuse and wrong handling can damage the sensor or lead to wrong measurement results. The measuring steering wheel...

 Open the catalog to page 4
Manual steering wheel-5

Product description A ATESTEO Risk of fatal injuries! All safety instructions must be followed strictly. • The airbag of the original steering wheel must be deactivated and removed before installation of the measuring steering wheel. Usage of the measuring steering wheel with airbag is strictly prohibited and can lead to death. • When using the adapter kit, the measuring steering wheel must be mounted fix on the original steering wheel. • Without using the adapter kit, the measuring steering wheel must be mounted fix on the original steering system. A safe mounting solution must be chosen by...

 Open the catalog to page 5
Manual steering wheel-6

Measurement body (torque sensor) The torque sensor contains the electronic for measuring the torque (strain gauges, amplifiers, and controller) and the angle. The sensor consists of a rotor and stator which are connected by bearings. Figure 1 Torque sensor (measuring steering wheel) without adapter kit The angle value is calculated based on an internal magnetic ring with encoder. This ring has two tracks (A/B). 2.2 Optional adapter kit components The adapter kit is optional. The components of this kit are used to install the measuring steering wheel on top of the original steering wheel. The...

 Open the catalog to page 6
Manual steering wheel-7

Figure 4 Spline (3x bended with 10°, 3x not bended) Figure 5 Clamping material set (3x) Figure 6 Mounting screws (12x) Figure 7 Steering wheel without airbag (MOMO) for attachment to torque sensor ATESTEO GmbH & Co. KG Measuring steering wheel – V 2.3 – 11/2026

 Open the catalog to page 7
Manual steering wheel-8

Figure 8 Torque sensor (with attached cover and connector disk) Figure 9 Complete system incl. adapter kit Optional remote control A remote control can be optionally ordered with the measuring steering wheel. With the remote control, the torque or angle value can be reset to zero by two individual push buttons. When connecting the VETAS with the remote control, each button will light up for 1 second as power indicator. During the operation with VETAS, each button can be used to trigger the zero-point adjustment (zero reset). Each reset will take up to 7 seconds. Wait until a reset is finished...

 Open the catalog to page 8
Manual steering wheel-9

A ATESTEO The default cable length of the remote control is 3m. Pin assignment of the remote control: Pin Table 1 Remote control pin assignment Measuring steering wheel - V 2.3 - 11/2026

 Open the catalog to page 9
Manual steering wheel-10

Equipment installation Equipment installation Mechanical installation with adapter kit Remove the airbag of the original steering wheel. Please follow the instructions of the vehicle manufacturer. Risk of fatal injuries! Airbag can explode when handled wrong during uninstallation. Installed airbag can cause death when used in combination with the measuring steering wheel! Once the airbag is removed, the installation of the measuring steering wheel can start. 3.1.1 Holder mechanism Take the connector disk (attached to the torque sensor) and fix three splines at the pre-defined positions. The bending...

 Open the catalog to page 10
Manual steering wheel-11

Equipment installation A ATESTEO Figure 12 Clamping components Table 2 Clamping components The sets must be installed with 120° angle between each other. It’s a good way to do the assembly with two persons. One person is holding the sensor, the other one is fixing a set. Assembly of one clamping set on the original steering wheel: Take the “fixing block” and hold it behind the original steering wheel. Attach the “Round connector” to the “Fixing block” at the front side of the steering wheel. Place the “Flat connector” on top of the rear side of the “Round connector”. Make sure the track in both...

 Open the catalog to page 11
Manual steering wheel-12

Equipment installation Figure 14 View onto a mounted clamping set on a spline If all three clamps are connected with the holder and the original steering wheel, check if the installation is concentric and the rotation of the steering wheel is possible without any blockade. The concentricity of the holder can be optimised by using the distance markers at each spline. Figure 15 Distance markers at a spline Once the holder and the clamps are connected together, make sure that all screws, the one at the disk and at the clamping mechanism are tightened well. Risk of fatal injuries! If screws are not...

 Open the catalog to page 12
Manual steering wheel-13

Equipment installation Figure 16 Assembly and material overview ATESTEO GmbH & Co. KG Measuring steering wheel – V 2.3 – 11/2026

 Open the catalog to page 13
Manual steering wheel-14

Equipment installation Figure 17 Finished sensor installation in a vehicle Steering wheel Figure 18 Steering wheel Place the steering wheel (MOMO) on top of the torque sensor (onto the cover, see Figure 2). Use screws of type M6x10 with countersunk head to fix the steering wheel (six screws). Risk of fatal injuries! If screws are not tightened well, steering control can be lost during driving! Risk of death. Check screws before every drive. ATESTEO GmbH & Co. KG Measuring steering wheel – V 2.3 – 11/2026

 Open the catalog to page 14

All ATESTEO GmbH & Co. KG catalogs and technical brochures

  1. Data sheet F6xS

    21  Pages

  2. Data sheet F4xS

    21  Pages

  3. Manual VETAS 3

    30  Pages

  4. Manual VECTO

    26  Pages

  5. Manual T series

    124  Pages

  6. Data sheet F5xS

    18  Pages

  7. Data sheet F3xS

    27  Pages

  8. Manual Fx series

    124  Pages

  9. Data sheet F2xS

    35  Pages

  10. Data sheet F1xS

    27  Pages

  11. Data sheet F0xS

    51  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.
About DirectIndustry
DirectIndustry is a marketplace that offers B2B players a complete experience, from product sourcing to purchase. DirectIndustry is an entity of VirtualExpo Group.