Safety StandardsElectrical Safety Compliance iiiiriii HypotULTRA' Series How To Use This Guide FIND the safety standard that applies to your product. Each page of this document details the electrical safety tests for various safety standards. REVIEW the electrical safety testing requirements for the standard and determine which tests you need to perform. MATCH these requirements with the Associated Research instrument that will fit your testing needs. If you need to perform multiple tests, look for a complete solution in the OMNIA® II Series or HypotULTRA® 7804/54 instruments. This document is meant for reference purposes only. It is not a replacement for the necessary safety standards. NOTE: This is an interactive PDF, please use our quick links to be brought to that Series web page to learn more about the instrument. 13860W.Laurel Drive, Lake Forest, IL 60045 USA Call +1-847-367-4077 Visit Us Online arisafety.com V2.3

YOUR COMPLETE SOLUTION 18.2.2 Test 1 Verification of the Continuity of the Protective Bonding Circuit (Ground Bond Test) REQUIREMENT PASS CRITERIA SOLUTION: HYAMP® 3240 18.3 Insulation Resistance Tests (IR Test) REQUIREMENT PASS CRITERIA Test voltage = 500 V DC IR value measured between power circuit conductors and grounding circuit Minimum insulation resistance ≥ 1 MΩ Exception - a value of 50 kΩ or more is allowed for certain parts of electrical equipment. See 18.3 for details. SOLUTION: HypotULTRA® 7850 or Hypot® 3870 18.4 Voltage Tests (Hipot Test) REQUIREMENT PASS CRITERIA Test voltage...

Visit Us Online arisafety.com

YOUR COMPLETE SOLUTION IEC 60598-1 7th Edition 7.2.3 Provisions for Earthing (Ground Bond Test) 10.2.1 Insulation Resistance (IR Test) 10.2.2 Electric Strength Test (Hipot Test) 10.3 Touch Current and Protective Conductor Current (Leakage Current Test)

YOUR COMPLETE SOLUTION IEC/UL 60950-1 2nd Edition 6-in-1 Instrument Visit Us Online arisafety.com

YOUR COMPLETE SOLUTION 5.6.3 Limit Values for Accessible Parts (Leakage Current Test) REQUIREMENT PASS CRITERIA Tested in Normal Conditions (NC) and Single Fault Conditions (SFC) Leakage Current (NC) ≤ 0.5 mA R.M.S. OR ≤ 0.7 mA Peak OR ≤ 2 mA DC Leakage Current (SFC) ≤ 3.5 mA R.M.S. OR 5 mA Peak OR 15 mA DC NOTE: AR Instruments contain leakage network A.1. Other networks must be manually built into our External MD. SOLUTION: LINECHEK® II 620L 6.5.2.4 Impedance of Protective Bonding of Plug Connected Equipment (Ground Bond Test) REQUIREMENT PASS CRITERIA Current = 25 A AC or DC or 2 * highest...

*Section 8.7 consists of a number of various leakage tests. Further details are given in the below diagram Visit Us Online arisafety.com

Earth Leakage Current: Figure 13, Section 8.7.4.5 Touch Current (Enclosure Leakage): Figure 14, Section 8.7.4.6 Patient Leakage General: Section 8.7.4.7 Patient Auxiliary (Patient Lead to Lead): Fig. 19, Section 8.7.4.8 Patient Lead to Earth: Fig. 15, Section 8.7.4.7a Mains on Applied Part (for F-Type Patient Leads): Fig. 16, Section 8.7.4.7b Mains on Signal I/O Ports: Fig. 17, Section 8.7.4.7c Mains on Non-Protectively Earthed Chassis Point: Fig. 18, Section 8.7.4.7d Production line testing is defined in Annex L for dielectric withstand testing . Other production line testing requirements are...

YOUR COMPLETE SOLUTION 17.2 Bonding Circuit Impedance (Ground Bond Test) 17.5 Insulation Resistance Test (IR Test - Mexico Only) 18 Factory Production Tests Visit Us Online arisafety.com