Data sheet ASO Safety Contact Mat
8Pages

Data Sheet Data sheet ASO Safety Contact Mat Used for safeguarding of hazardous areas Prevents hazardous motion by triggering stop signals Material assures impermeability of oils, water and dirt Individual designs, various switching zones and full or partly colored mats are possible Additional checkered surface materials: High grade steel and aluminum

The main principle of an ASO Safety Contact Mat incl. structure-surface The basic design principle of the SENTIR mat consists of two conductive plates which are separated by a rasterized insulating layer. These plates are completely molded in a polyurethane material so they are impervious to oil, water and dirt. The surface is composed slip resistant and provides excellent resistance against oil and grease. Cable exits can be placed up to your demands. Usually SENTIR mat is provided with corner cable exits and M8 male & female connectors. Either molded or aluminum ramp rails can be used to...

Data Sheet SENTIR mat 14 Ramp rail RS 14 Marking groove Cable duct Connection cable Fixation sleeve (available on request) SENTIR mat 14 ARB (SENTIR mat 14 TBV) Ramp rail RS 14 Marking groove Steel plate Cable duct Connection cable Technical specifications for Safety contact mats SENTIR mat 14 / 14 T / 14 U Max. dimension Standard dimensions available from stock Construction height Inactive edge Switching pressure Static load Test piece ∅ 80 mm = approx. 150 N max. 2000 N on ∅ 80 mm * Response time Test piece ∅ 80 mm = approx. 150 N max. 2000 N on ∅ 80 mm * Switching cycles Electrical...

Data Sheet Order key Corner connector „EVA“ 1. Description ASO-Safety Contact Mat 2. Construction Height e.g. 14 mm 3. Number of switch zones within one mat 4. Materials ground plate T : With molded ramp rail : 1x double-core cable connection : 1x cable connection + internal end resistor : 2x double-core cable connection : 1x cable connection with external resistor 4.0 : 1x M8 connector male and 1x M8 connector female 4.2 : (like 4.0) with M8 connection cable 2,5 m 4.3 : (like 4.0) with 5 m cable, M8 connector female and M8 resistor plug 4.4 : (like 4.0) with 5 m cable, M8 connector male...

Data Sheet Technical data of accessories Ramp rail RS 14 Applicable to: Artilel-No.: Material: Standard delivery length: Weight: SENTIR mat 14 ARB / 14 TBV / 14 NP 603003 Aluminum AlMgSi 0,5 3 m / 6m Ca. 411 g/serial meter SENTIR mat 14 ARB / 14 TBV / 14 NP 603001 Aluminum AlMgSi 0,5 3 m / 6 m Ca. 788 g/serial meter 3 sealing plugs/serial meter Applicable to: Artilel-No.: Material: Standard delivery length: Weight: Accessories: Corner connector EVA SENTIR mat 14 ARB / 14 TBV / 14 NP 603020 PA 6 30% DV, black Artilel-No.: Material: Applicable to: Artilel-No.: Material: Weight: ARB surface...

MOUNTING INFORMATION The mounting surface has to be absolutely even, clean and dry. Lay out and position the mat correctly. Mats may not be folded or bent. Safety-Contact-Mats may not be manipulated in any way. Cut outs or shortening is not possible beside shown Flatness tolerance forsubfloor (according to DIN 18202) Please note for measurement: The ramp rail respectively fixation rail is needed to fix the mat to the floor. Subsequently the total space required is calculated by adding up the zone to be guarded (nominal dimension of mat) and the width of the ramp rail or fixation rail....

Data Sheet Assembly of SENTIR mat 14 When using corner connectors the ramp rail has to be shortened 20mm for each corner connector. Insert the cable-near corner connector from above to make sure the cable is led through the cable duct (fig. 1). Then attach the ramp rail to the ground with 6mm dowels and appropriate screws. Adjust the ramp rail laterally to the mat and plug it on the guiding pin (fig. 2). Mark the fastening points (One each 60 cm) on the center line of the ramp rail and pre-drill 10 mm for the sealing plugs. Then again attach the ramp rail to the ground with 6 mm dowels and...

Data Sheet Mounting of SENTIR mat 14 T with molded ramp rail Please note for oversize: The total space requirement of a SENTIR mat with molded ramp rail results from the space of the area to be safeguarded (nominal dimension of mat) and the width of the ramp rail. The width of the ramp rail RS 14 is 35 mm (fig. 7). In order to avoid any clamping or pinching of the cables, cut the cable outlet on required side (fig. 8). cut out Technical changes reserved Installation Adjust the SENTIR mat according to your needs and fix them to the floor with adequate dowels and screws (fig. 9). = coming out...