posiwire® Cable Extension Position Sensors WS17KT Displacement sensor with measurement length up to 15,000 mm Aluminum housing With precision potentiometer Optional with integrated brake Product versions Analog output, SSI

WS17KT - Cable Extension Position Sensor Version with analog output, SSI output Specifications Order options Measurement range Analog: quasi infinite Potentiometer 1 kΩ Voltage 0 ... 10 V Current 4 ... 20 mA, 2 wire Current 4 ... 20 mA, 3 wire Current output, programmable Voltage output, programmable Signal conditioner SSI 12 bit Signal conditioner SSI 14 bit Signal conditioner SSI 16 bit Sensing device Precision potentiometer Aluminum measuring cable: stainless steel Protection class Cable fixing M4 cable fixing Cable clip Temperature range see table "Cable forces" Order example: WS17KT – 2500...

Cable forces typical at = 20 °C Maximum pull-out force [N] Minimum pull-in force [N]

posiwire® WS17KT Dimensions Measurement range 1500 … 2000 … 2500 mm Measurement range Dimensions in mm [inch] Dimensions informative only. For guaranteed dimensions consult factory.

posiwire® WS17KT Measurement range 3000 ... 4000 mm Measurement range Dimensions in mm [inch] Dimensions informative only. For guaranteed dimensions consult factory.

posiwire® WS17KT Measurement range 5000 … 6250 mm Measurement range Dimensions in mm [inch] Dimensions informative only. For guaranteed dimensions consult factory.

posiwire® WS17KT Measurement range 10000 … 12500 … 15000 mm Dimensions in mm [inch] Dimensions informative only. For guaranteed dimensions consult factory.

posiwire® WS17KT Output specifications Analog outputs Voltage divider R1K Excitation voltage Potentiometer impedance Thermal coefficient Depends on the measuring range, individual sensitivity of the sensor is specified on the label Voltage divider utilization range Operating temperature Refer to output specification The potentiometer must be connected as a voltage divider! The following processing circuit has to be implemented according to the circuit scheme in the Appendix (see „Output information“)! Electrical current flow impact on the wiper causes linearity errors and shortens the lifetime...

Excitation voltage Voltage output Excitation current Output voltage Output current Output load Stability (temperature) Reverse polarity, short circuit Output noise Operating temperature Refer to output specification Signal wiring Connector M12, 8 pin Cable color Not connected View to the soldering side of mating connector Output signals *: internally connected

Excitation voltage 18 ... 27 V DC non stabilized, measured at the sensor terminals Excitation current Output current Stability (temperature) Reversed polarity, short circuit Output noise Operating temperature Refer to output specification Current output (2 wire) Signal wiring Connector M12, 8 pin Cable color View to the sensor connector Output signals

Excitation voltage Current output (3 wire) Excitation current Load resistor Output current Stability (temperature) Reverse polarity, short circuit Output noise Operating temperature Refer to output specification Signal wiring Connector M12, 8 pin Cable color View to soldering side of mating connector Output signals *: internally connected

Excitation voltage Voltage output programmable Excitation current Voltage output PMUV Output current Output load Current output PMUI Working resistance Current output programmable Scaling Activation of offset and gain adjust Connect with excitation GND (0 V) Scalable range Stability (temperature) Operating temperature Refer to output specification Reversed polarity, short circuit PMUV / PMUI Signal wiring Connector M12, 8 pin Cable color ZERO View to soldering side of mating connector Output signals *: internally connected PMUI2 Signal wiring Connector M12, 8 pin Cable color Signal GND* View...

Outputs .../PMUV, PMUI, PMUI2 Programming of the start and end value by the customer Teach-In of start and end value for the outputs PMUV, PMUV and PMUI2 is provided by two binary signals ZERO and END. At the start position connect signal ZERO for a short period to GND via push button. At the end position connect signal END for a short period to GND. The scaling range will be stored non-volatile. To reset the sensor to factory default both signals ZERO and END must be connected to ground while powering up the sensor.

posiwire® WS17KT Digital Interfaces ADSI Excitation volatge A/D converted synchronous serial Excitation current Clock frequency Gray-Code, continuous progression Delay between pulse trains ADSI16: 16 bit (65536 counts) f.s. ADSI14: 14 bit (16384 counts) f.s. ADSI: 12 bit (4096 counts) f.s. Stability (temperature) Operating temperature Data format (train of 26 pulses) Transmission rate Baud rate Signal wiring Connector M12, 8 pin Cable length Extension of the cable length will reduce the maximum transmission rate. Cable color View to soldering side of mating connector Output signals

posiwire® WS17KT Accessories Connector cable M12, 8 pin (angular coupling) shielded connector The 8-lead shielded cable is supplied with a mating 8-pin 90° M12 connector at one end and 8 wires at the other end. Available lengths are 2 m, 5 m and 10 m. Wire: cross sectional area 0.25 mm² Cable diameter: 6.3 ±0.2 mm Order code KAB - xM - M12/8F/W - LITZE IP69: KAB - xM - M12/8F/W/69K - LITZE xM = length in m Connector cable M12, 8 pin (straight coupling) shielded connector The 8-lead shielded cable is supplied with a mating 8-pin M12 connector at one end and 8 wires at the other end. Available...

posiwire® WS17KT Plug-in connectors Plug-in connector M12, 8 pin (straight coupling) Order code: