Catalogs >
ASC >
ASC 5411LN / ASC 5415LN

ASC 5411LN / ASC 5415LN
3Pages

Catalog excerpts

MEMS Capacitive Accelerometer ► Triaxial ► Ultra Low Noise (LN) ► High g-Range ► 8 or 12 Wire System ► Amplified Output ► Aluminium Housing / Stainless Steel Housing ► Made in Germany Features ► Range: ±2g to ±400g ► DC Response ► High Shock Resistance ► Gas Damped ► Excellent Bias and Scale Factor Stability ► Differential Mode Options ► Customised Cable Length ► Customised Connector ► TEDS Module Applications ► Structural Monitoring and Testing ► Endurance Testing ► Brake Test ► Vibration Monitoring ► Civil Engineering ► Modal Analysis ► Vehicle Testing ► Automotive Ride Quality & Comfort ► Railway Engineering ► Flutter Test Capacitive MEMS Technology The accelerometers are based on a capacitive MEMS technology and can be used in a low frequency response up from 0Hz. Inside the sensor element, the seismic mass is connected with two conductive capacitor plates. If the seismic mass oscillates between the two capacitor plates the capacitance will change. This capacitance change is converted via an ASIC (Application Specific Integrated Circuit) into an analog signal. Description The models ASC 5411LN and ASC 5415LN have been developed for the demanding requirements of different applications. The highly robust housing and the connecting cables are suitable for the rough application areas in automotive, train, military an so on. These ASC accelerometers benefit from the high stability of the chip technology with a low noise level and a low bias and an excellent scale factor temperature coefficient. The ASC 5411LN and ASC 5415LN are fully compensated over a wide temperature range and are factory calibrated. As capacitive technology is used, extremely small measuring ranges are possible. The amplified output is easy to use with a data acquisition unit. The signal is independent from the power between 8VDC to +30VDC. The package is hard anodized aluminium that is rugged for automotive, industrial and military applications. A very high flexible and rugged cable provides a simple mounting. ASC 5411LN and ASC 5415LN are equipped with 6 meter cable as standard. ASC GmbH ■ Advanced Sensors Calibration ■ Ledererstra&e 10 ■ 85276 Pfaffenhofen ■ Germany ■ Tel. +49 (0) 8441 786 547 -0 ■

Open the catalog to page 1

Typical Specifications DYNAMIC Range (±g) 2 5 10 25 50 100 200 400" ELECTRICAL Excitation voltage V DC 8-30 Zero acceleration output ±mV 150 150 80 80 80 80 80 80 Isolation Case Isolated Residual / Broadband noise (±5% frequency range) |jV 100 60 70 90 100 100 125 125 ENVIRONMENTAL Thermal sensitivity shift %/°C 0.015 Thermal zero shift mg/°C 0.15 0.4 0.75 2 4 7.5 15 30 Operating temperature range °C -40°C to +100°C Storage temperature range °C -55°C to +125°C...

Open the catalog to page 2

FACTORY CALIBRATION (SUPPLIED WITH THE SENSOR) Range 2g and 5g 10g 25g 50g and 100g 200g and 400g CALIBRATION DIN ISO 17025 (ORDER SEPARATELY) Range 2g and 5g 10g Sensitivity at 16Hz and 0.5g at 80Hz and 5g Cable Code /Pin Configuration 8-wiring-System Red Supply + Black Supply - White/Violet Signal - White/Grey Signal - White Signal - Supply + Supply -Signal + Signal - Supply + Supply -Signal + Signal - Supply + Supply -Signal + Signal - ORDERING INFORMATION ASC - 5411LN (Low Noise) Model number Cable length (meters) Connector & Pinout ASC GmbH ■...

Open the catalog to page 3